Filter
Top Products
Teledyne API M100E Analyzer Operation Manual Table of Contents
ix
Figure 7-6: Rear Panel Connector Pin-Outs for COM2 in RS-485 Mode ................................................... 123
Figure 7-7: CPU Connector Pin-Outs for COM2 in RS-485 Mode.............................................................. 124
Figure 7-8: COMM – LAN / Internet Configuration Properties .................................................................... 127
Figure 7-9: COMM – Manually Configuring the Network IP Addresses (Step 1)........................................ 128
Figure 7-10: COMM – Manually Configuring the Network IP Addresses (Step 2)........................................ 129
Figure 7-11: COMM – Change Host Name.................................................................................................. 130
Figure 7-12: Location of JP2 on RS232-Multidrop PCA (OPT 62)................................................................ 133
Figure 7-13: RS232-Multidrop PCA Host/Analyzer Interconnect Diagram ................................................... 134
Figure 7-14: COMM – Enable Hessen Protocol (Example) .......................................................................... 136
Figure 7-15: COMM – COMM Port Baud Rate ............................................................................................. 137
Figure 7-16: COMM – COMM Port Baud Rate ............................................................................................. 138
Figure 7-17: Default iDAS Channels Setup................................................................................................... 143
Figure 7-18: iDAS – Data Acquisition Menu................................................................................................. 144
Figure 7-19: iDAS – Editing iDAS Data Channels........................................................................................ 145
Figure 7-20: iDAS – Editing Data Channel Name........................................................................................ 146
Figure 7-21: iDAS – Trigger Events ............................................................................................................. 147
Figure 7-22: iDAS – Editing iDAS Parameters............................................................................................. 148
Figure 7-23: iDAS – Configuring Parameters for a Specific Data Parameter .............................................. 149
Figure 7-24: iDAS – Define the Report Period............................................................................................. 151
Figure 7-25: iDAS – Define the Report Period............................................................................................. 152
Figure 7-26: iDAS – RS-232 Report Function.............................................................................................. 153
Figure 7-27: iDAS – Disabling / Enabling Data Channels............................................................................ 154
Figure 7-28: iDAS – Holdoff Feature............................................................................................................ 155
Figure 7-29: Sample APICOM User Interface for Configuring the iDAS....................................................... 156
Figure 7-30: iDAS Configuration Through a Terminal Emulation Program................................................... 157
Figure 7-31: Status Output Connector .......................................................................................................... 158
Figure 7-32: Control Inputs with Local 5 V Power Supply............................................................................. 160
Figure 7-33: Control Inputs with External 5 V Power Supply ........................................................................ 160
Figure 7-34: COMM – Remote Access by Modem ....................................................................................... 164
Figure 7-35: COMM – Initialize the Modem .................................................................................................. 165
Figure 7-36: APICOM Remote Control Program Interface............................................................................ 167
Figure 7-37: COMM – Activating Hessen Protocol ....................................................................................... 169
Figure 7-38: COMM – Select Hessen Protocol Type.................................................................................... 170
Figure 7-39: COMM – Select Hessen Protocol Response Mode.................................................................. 171
Figure 7-40: COMM – Status Flag Bit Assignment ....................................................................................... 173
Figure 8-1: Setup for Manual Calibration without Z/S Valve or IZS Option (Step 1)................................... 177
Figure 8-2: Setup for Manual Calibration without Z/S Valve or IZS Option (Step 2)................................... 177
Figure 8-3: Setup for Manual Calibration without Z/S Valve or IZS Option (Step 3)................................... 178
Figure 8-4: Setup for Manual Calibration Checks ....................................................................................... 179
Figure 8-5: Setup for Manual Calibration with Z/S Valve Option Installed (Step 1).................................... 180
Figure 8-6: Setup for Manual Calibration with Z/S Valve Option Installed (Step 2).................................... 180
Figure 8-7: Setup for Manual Calibration with Z/S Valve Option Installed (Step 3).................................... 181
Figure 8-8: Manual Calibration with IZS Option .......................................................................................... 182
Figure 8-9: Setup for Manual Calibration Check with Z/S Valve or IZS Option (Step 1) ............................ 183
Figure 8-10: Setup for Manual Calibration Check with Z/S Valve or IZS Option (Step 2) ............................ 184
Figure 8-11: Manual Calibration in Dual/Auto Reporting Range Modes....................................................... 185
Figure 8-12: AUTO CAL – User Defined Sequence...................................................................................... 188
Figure 8-13: O
2
Sensor Calibration Set Up ................................................................................................... 189
Figure 8-14: O
2
Span Gas Concentration Set Up ......................................................................................... 190
Figure 8-15: Activate O
2
Sensor Stability Function ....................................................................................... 191
Figure 8-16: O
2
Zero/Span Calibration.......................................................................................................... 192
Figure 8-17: CO
2
Sensor Calibration Set Up................................................................................................. 193
Figure 8-18: CO
2
Span Gas Concentration Setup ........................................................................................ 193
Figure 8-19: Activate CO
2
Sensor Stability Function .................................................................................... 194
Figure 8-20: CO
2
Zero/Span Calibration ....................................................................................................... 195
Figure 9-1: Dynamic Multipoint Span Calibration........................................................................................ 204
Figure 10-1: Sample Particulate Filter Assembly.......................................................................................... 212
Figure 10-2: Critical Flow Orifice Assembly .................................................................................................. 214
04515F DCN6048