Filter
Top Products
Model GFC7000E Instruction Manual GFC7000E Documentation
04584 Rev A1 ix
Table 6-2: Test Functions Defined................................................................................... 46
Table 6-3: List of Warning Messages ............................................................................... 49
Table 6-4: Primary Setup Mode Features and Functions ..................................................... 52
Table 6-5: Secondary Setup Mode Features and Functions ................................................. 52
Table 6-6: Variable Names (VARS) Revision B.3 ............................................................... 64
Table 6-7: GFC7000E Diagnostic (DIAG) Functions............................................................ 66
Table 6-8: DIAG - Analog I/O Functions........................................................................... 69
Table 6-9: Analog Output Voltage Ranges........................................................................ 69
Table 6-10: Analog Output Current Loop Range.................................................................. 70
Table 6-11: Analog Output Pin Assignments....................................................................... 70
Table 6-12: Voltage Tolerances for Analog Output Calibration............................................... 73
Table 6-13: Current Loop Output Calibration with Resistor ................................................... 76
Table 6-14: Test Parameters Available for Analog Output A3 ................................................ 81
Table 6-15: COM1 and COM2 DB-9 Pin Assignments............................................................ 85
Table 6-16: COMM Port Communication modes................................................................... 86
Table 6-17: Ethernet Status Indicators.............................................................................. 89
Table 6-18: LAN/Internet Configuration Properties .............................................................. 90
Table 6-19: Internet Configuration Keypad Functions .......................................................... 94
Table 6-20: CO
2
Concentration Alarm Default Settings......................................................... 95
Table 6-21: Front Panel LED Status Indicators for iDAS ....................................................... 96
Table 6-22: iDAS Data Channel Properties ......................................................................... 97
Table 6-23: iDAS Data Parameter Functions....................................................................... 98
Table 6-24: Status Output Pin Assignments ..................................................................... 116
Table 6-25: Control Input Pin Assignments ...................................................................... 116
Table 6-26: Terminal Mode Software Commands .............................................................. 118
Table 6-27: Command Types ......................................................................................... 119
Table 6-28: Serial Interface Documents........................................................................... 123
Table 6-29: RS-232 Communication Parameters for Hessen Protocol ................................... 124
Table 6-30: Teledyne Instruments Hessen Protocol Response Modes ................................... 126
Table 6-31: Default Hessen Status Bit Assignments........................................................... 127
Table 7-1: AUTOCAL Modes ......................................................................................... 139
Table 7-2: AutoCal ATTRIBUTE Setup Parameters ........................................................... 139
Table 7-3: Calibration Data Quality Evaluation................................................................ 142
Table 9-1: GFC7000E Maintenance Schedule .................................................................. 146
Table 9-2: GFC7000E Test Function Record.................................................................... 147
Table 9-3: Predictive uses for Test Functions.................................................................. 148
Table 10-1: Sync/Demod Status LED Activity ................................................................... 168
Table 10-2: Relay Board Status LED’s ............................................................................. 169
Table 10-3: Front Panel Status LED’s .............................................................................. 176
Table 11-1: Warning Messages - Indicated Failures ........................................................... 185
Table 11-2: Test Functions - Indicated Failures................................................................. 187
Table 11-3: Sync/Demod Board Status Failure Indications ................................................. 190
Table 11-4: I
2
C Status LED Failure Indications ................................................................. 191
Table 11-5: Relay Board Status LED Failure Indications ..................................................... 192
Table 11-6: DC Power Test Point and Wiring Color Codes ................................................... 200
Table 11-7: DC Power Supply Acceptable Levels ............................................................... 200
Table 11-8: Relay Board Control Devices ......................................................................... 201
Table 11-9: Opto Pickup Board Nominal Output Frequencies............................................... 202
Table 11-10: Analog Output Test Function - Nominal Values Voltage Outputs.......................... 204
Table 11-11: Analog Output Test Function - Nominal Values Current Outputs ......................... 205
Table 11-12: Status Outputs Check .................................................................................. 205
Table 12-1: Static Generation Voltages for Typical Activities ............................................... 214
Table 12-2: Sensitivity of Electronic Devices to Damage by ESD ......................................... 214
Table A-1: GFC7000E Setup Variables, Revision E.0 ........................................................ 231