Filter
Top Products
Index-6 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide
I
IAM. See initial address message (IAM)
ICD. See Internet Call Diversion (ICD)
ICMP redirects, configuring system to ignore
, 1-9
Idle mode for T1 lines
, 7-5, 7-22
IDSL
incoming voice calls
, 17-18
outgoing voice calls
, 17-18
supported CPE devices
, 17-4
voice connections, configuring
, 17-17
See also DSL
IDSL card
configuring static route to gateway
, 17-25
connectors
, 17-2
emulates 5ESS switch
, 17-21, 17-25
features
, 17-2
overview
, 17-1
remote devices it supports
, 17-1
sample configuration
, 17-22
sample configuration for Pipeline
, 17-21, 17-25
signaling used
, 17-1
switch type to use for remote device
, 17-21, 17-25
transmission speeds and distances
, 17-1
IDSL profile, sample configuration
, 17-24
inactivity timer, for DSL
, 17-4
Inband signaling, call control
, 7-11
Internet call diversion (data). See data
IP
E1 FrameLine card and routing
, 10-2
FrameLine card and routing
, 8-2
soft interface address
, 2-5
IP address
assigning system
, 1-4
requiring caller to accept dynamic
, 1-9
verifying with Ping
, 1-7
IP interfaces, multiple per Ethernet port
, 4-3
IPDC. See IP Device Control (IPDC)
IP-Interface profile, assigning
, 2-4
IP-Interface profile, described
, 4-3
IP-Route profile, name of default
, 1-6
ISDN
call-type used to route calls
, 19-13
configuring multiple NFAS groups
, 7-13
configuring single NFAS group
, 7-13
data sense
, 7-22
example NFAS configuration
, 7-13
example PRI configuration
, 7-8, 9-8, 9-9
signaling
, 9-8
subaddress used to route calls
, 19-12
ISDN D channel
inverting data on
, 7-22
sharing signaling among T1 lines
, 7-13
specifying idle pattern
, 7-22
ISDN PRI
overview
, 7-2, 9-2
setting channel 24 as D channel
, 7-8
specifying for E1 lines
, 9-12
specifying signaling for T1 lines
, 7-8
ISDN TAs, connecting via IDSL
, 17-4
ITU-T. See International Telecommunications Union
Telecommunication Standardization Sector (ITU-T)
L
LAN IP interfaces
directed broadcasts, disabling
, 1-9
leased connections
example channel configuration
, 7-21, 9-16
example T1 channel configuration
, 7-21
nailed group for E1 channels
, 9-4
nailed group for T1 channels
, 7-5
leased line
channels must be contiguous
, 7-21, 9-15
configuring
, 7-21, 9-15
line speeds, configuring DSL
, 17-6
Line Status
E1 profile name displayed in
, 9-7
T1 profile name displayed in
, 7-7
lines
enabling E1
, 9-7
enabling serial WAN
, 12-4
enabling T1
, 7-8
enabling T3
, 11-5
enabling UDS3
, 13-2
SNMP support for T1
, 11-1
line-side T1
call control
, 7-11
described
, 7-2
List command, using
, 7-6
log level
setting
, 1-5
setting system
, 1-5
log messages
fan tray
, 3-3
long haul transceiver, described
, 9-13
loopback parameter
enable/disable, OC3-ATM
, 15-2
M
management, shelf controller Ethernet port for, 1-4
mark pattern, described
, 7-22
master clock source, specifying
, 7-17