Filter
Top Products
Index-2 APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide
bearer capability and, 9-10
signaling modes described
, 9-8
cause codes
access SS7 gateway control protocol (ASGCP) calls
,
18-19
disconnect, signaling system 7 (SS7) support for call
ID
, 18-20
CCITT. See Consultative Committee for International
Telephone and Telegraph
cell payload parameter
enable/disable
, 14-3
channel usage
for E1 channels
, 9-4, 9-14
for T1 channels
, 7-4, 7-18
specifying for E1 lines
, 9-14
specifying for T1 lines
, 7-18
channelized T1
configuration
, 7-11
described
, 7-2
See also T1
channels
must be contiguous in nailed line
, 7-21, 9-15
number of nailed on both ends
, 7-21, 9-15
CIC. See circuit identification code (CIC)
clock source
displaying current
, 7-17, 9-13
for E1 lines
, 9-13
for T1 lines
, 7-4, 7-17
using an internal clock source
, 7-17, 9-13
clocking
configuring
, 7-17
example configuration
, 11-5
FrameLine card and
, 8-3, 10-6
how system chooses a source
, 7-17, 9-13
serial WAN internal
, 12-5
Clock-Priority
OC3-ATM supporting
, 15-3
Clock-Priority setting
, 15-3
Clock-Source
OC3-ATM profiles
, 15-3
Clock-Source command, using
, 7-17, 9-13
Clock-Source parameter
, 15-3
OC3-ATM ports
, 15-3
CO. See central office (CO)
codecs, specifying analog encoding
, 7-22, 9-16
command line interface, overview of use
, 7-6
command-line interface, switching primary controller
,
2-8
commands
Clock-Source
, 7-17, 9-13
Dir
, 7-6, 9-5
fanstatus
, 3-4
List
, 7-6
output, samples
, 18-15
output, showing errors
, 18-18
Read and Write
, 2-4
repeating
, 7-21, 9-15
Set
, 2-4
ss7nmi debug-level
, 18-15
Thermalstatus
, 3-5
Write
, 7-6
community strings, read and read-write
, 1-11
compression
FrameLine card and
, 8-2, 10-2
configuration
APX 8000 shelf-controller redundancy
, 2-3
assigning system IP address for APX 8000, redundant
shelf-controllers
, 2-4
basic signaling system 7 (SS7)-Gateway profile,
example
, 18-8
DPNSS signaling
, 9-12
E1 FrameLine card overview
, 10-2
E1 line, SS7 data trunk
, 18-11
E1 PRI
, 9-7, 9-8, 9-9
E1 signaling system 7 (SS7) data trunks
, 18-10
enabling a E1 line
, 9-7
enabling a serial WAN line
, 12-4
enabling a T1 line
, 7-8
enabling a T3 line
, 11-5
enabling a UDS3 line
, 13-2
example T1
, 7-23
fan tray, example
, 3-2
FrameLine card overview
, 8-2
inband robbed-bit (T1)
, 7-11
ISDN NFAS (T1)
, 7-13
listing parameters using the List command
, 7-6
nailed channels
, 7-21, 9-15, 9-16
OC3-ATM configuration
, 15-4
overview of DS3-ATM
, 14-3
overview of E1
, 9-2
overview of Ethernet card
, 4-2
overview of serial WAN card
, 12-1
overview of T1
, 7-3
overview of T3
, 11-1
overview of UDS3
, 13-2
performing basic
, 1-1
phone numbers
, 7-19, 9-14
Physical interface profiles, for shelf-controller
redundancy
, 2-6
PRI (E1)
, 9-8
profiles, shelf-controller redundancy
, 2-6
R2 signaling
, 9-11
reading in profile to edit it
, 7-6
Redundancy profile, for shelf-controller redundancy
,
2-6
sample IDSL
, 17-22
sample SDSL
, 17-29, 17-34
sample serial WAN
, 12-6
saving changes using the Write command
, 7-6