Filter
Top Products
APX 8000/MAX TNT/DSLTNT Physical Interface Configuration Guide Index-3
serial WAN card configuration requirements, 12-2
setting date and time
, 1-5
setting log level
, 1-5
shelf-controller redundancy
, 2-1, 2-6
signaling interface parameters
, 18-5
signaling system 7 (SS7) gateway
, 18-4
specifying default gateway
, 1-6
specifying digital modem negotiation
, 5-2
specifying DNS information
, 1-6
specifying IP address of shelf controller
, 1-4
specifying name
, 1-5
T1 data trunk for signaling system 7 (SS7) data,
example
, 18-9
T1 lines, signaling system 7 (SS7) data trunks
, 18-8
T1 parameters ignored for T3
, 11-3
T1 PRI
, 7-8
T3 card for signaling system 7 (SS7) data, example
,
18-9
T3 requirements
, 11-2
thermal controls, example
, 3-2
transport-layer options
, 18-6
understanding E1 requirements
, 9-4
using the command line interface
, 7-6
Connection profiles
configuring to use nailed channels
, 7-21, 9-16
sample for IDSL connection
, 17-19, 17-23
connections
back-to-back T1
, 7-21
configuring DSLPipe for ADSL
, 17-28
configuring DSLPipe for SDSL
, 17-33, 17-36
DSL Plug and Play
, 17-12
nailed DSL
, 17-5
nailed group used for ADSL
, 17-27
sample nailed PPP over ADSL
, 17-26
serial WAN card support
, 12-2
switch type for remote device in IDSL configuration
,
17-21, 17-25
switched DSL
, 17-4
continuity testing
, 18-4
control protocol
signaling system 7 (SS7)
, 18-6
controller status
viewing
, 2-10
CSU
specifying build-out
, 7-17
See also Front-end
D
D channel
inverting data on
, 7-22
sharing among PRI lines
, 7-13
specifying channel for PRI signaling
, 7-8
specifying idle pattern
, 7-22
DASS-2
configuring back-to-back connection
, 9-7
required settings
, 9-12
data sense (T1)
, 7-22
data transfer
configuring ADSL rates
, 17-6
per-session rate, configuring
, 17-8
rates for ADSL-CAP
, 17-2
rates for ADSL-DMT
, 17-2
rates for IDSL
, 17-1
rates for SDSL
, 17-3
rates for SDSL-HS
, 17-3
rates optimized by RADSL
, 17-2
SDSL rates, configuring
, 17-7
date and time, setting system
, 1-5
DDL. See data delivery layer (DDL)
default gateway, assigning system
, 1-6
defining soft IP interface for fault tolerance
, 2-5
denial of service attack, protecting system from
, 1-9
DHCP, server requirement for DSL Plug and Play
, 17-13
diagnostics, specifying messages to display
, 1-5
dialed digits, do not forward to system
, 7-11
digital milliwatt (DMW) tone
support on T3
digital millwatt tone (DMW)
T1 support
, 18-13
T3 support
, 18-13
Dir command, using
, 7-6, 9-5
directed broadcasts, disabling
, 1-9
disconnect cause codes
, 18-21
DLCIs
number supported on E1 FrameLine card
, 10-2
number supported on T1 FrameLine card
, 8-2
DMW. See digital milliwatt (DMW)
DNS
adding system to
, 1-4
configuring basic
, 1-6
DPC. See destination point code (DPC)
DPNSS
configuring back-to-back connection
, 9-7
example
, 9-12
required settings
, 9-12
DS3. See T3; DS3-ATM; STM-0
DS3-ATM
framing formats
, 14-2
parameters
, 14-1
DS3-ATM card
connecting redundantly to the WAN
, 14-3
DS3-ATM configuration, example
, 14-3
DS3-ATM interface
cell payload parameter
, 14-3
enable/disable parameter
, 14-2