Filter
Top Products
⎯ 101 ⎯
6 F 2 S 0 8 5 7
H D L C ( -132):1
_
9
:
I E C
(
-
0
254
)
:
2
3
/
A d d r e s s e r * *
/
Paramet
/
1
9 9 9 9 m s
S Y A D J (
-9
0
99):
:
0
-
I P 1
- 1
(
-
0
254
)
:
0
I P 1
-
(
-
0
254
)
:
0
I P 1
- 3
(
-
0
254
)
:
0
I P 1
-
4
(
-
0
254
)
:
0
S M 1
-
1
(
-
0
254
)
:
0
S M 1
-
(
-
0
254
)
:
0
S M 1
-
3
(
-
0
254
)
:
0
S M 1
-
4
(
-
0
254
)
:
0
G W 1
-
1
(
-
0
0
G W 1
-
2
(
-
0
0
G W 1
-
3
(
-
0
254
)
:
0
G W 1
-
4
(
-
0
254
)
:
2
2
254
)
:
254
)
:
0
S I 1
-
1
(
-
0
2
5
4
)
:
0
S I 1
-
2
(
-
0
2
5
4
)
:
0
S I 1
-
3
(
-
0
254
)
:
0
S I 1
-
4
(
-
0
2
5
4
)
:
S I 4 -
1
(
-
0
2
5
4
)
:
0
S I 4 - 2
(
For SNTP server 4
-
0
254
)
:
0
S I 4 -
3
(
-
0
254
)
:
0
0
S I 4 - 4
(
-
0
254
)
:
0
S M O D E (
-
0
1):
6s
G O I N T
(
-
1
0
60
)
:
P G 1 -
1
(
-
0
254
)
:
0
P G 1 - 2
(
For channel 1(port 1)
-
0
254
)
:
0
P G 1 -
3
(
-
0
254
)
:0
0P G 1 - 4
(
-
0
254
)
For channel 1(port 1)
For SNTP server 1
• Enter the address number on "HDLC" column for RSM and/or "IEC" column for
IEC60870-5-103 and the compensation value on "SYADJ" column for adjustment of time
synchronization of protocol used (
−: lags the time, +: leads the time).
Enter IP address for IP1-1 to IP1-4, Subnet mask for SM1-1 to SM1-4, Default gateway for
GW1-1 to GW1-4, and SNTP server address for SI1-1 to SI4-4. Four SNTP servers are
available.
Enter "0" or "1" on "SMODE" column to set the standard time synchronized mode for SNTP
server. Using low accuracy level of time server, synchronized compensation to maintain
synchronization accuracy may not be done automatically. Therefore enter "1", and
synchronized compensation is done forcibly. The default setting is "0".
Enter the time on "GOINT" to set the maximum GOOSE message publishing term if GOOSE
message receive checked.
Enter the IP address of the device for PG1-1 to PG1-4 if Ping response checked.
IP address:
∗∗∗, ∗∗∗, ∗∗∗, ∗∗∗
IP1-1 IP1-2 IP1-3 IP1-4
SM1-1 to SM1-4, GW1-1 to GW1-4, SI1-1 to SI4-4, PG1-1 to PG1-4: same as above.
• Press the
ENTER
key.
CAUTION: Do not overlap the number in a network.
• Press 2 (= Switch) on the "Communication" screen to select the protocol, transmission speed