Tektronix WFM 601E Wheelchair User Manual


 
Index
WFM 601A, WFM 601E & WFM 601M User Manual
Index–7
SLM:LEVEL?, C–5
SLM:RCVR, C–4
SLM:SOURCE?, C–4
SWEEP:MAG, C–49
SWEEP:TIMING, C–48
User Interface menu commands, C–14
Variable GAIN state for Lightning display, C–37
Variable GAIN state for the WFM and VEC displays,
C–36
Variable GAIN value for the Lightning display, C–37
Variable GAIN value for WFM and VEC displays,
C–36
VECtor:BARS, C–10
VECtor:GRAT, C–11
Voltage and timing cursor positioning, C–18
Voltage and timing cursor tracking, C–19
Remote operation, B–1
Rename, Preset function, 3–43
Renaming, Preset, 3–43
Repackaging for Shipment, 1–10
Replacing
fuse, D–1
graticule light bulbs, D–2
Reset, Serial format checks, 3–46
Restoring, front panel settings from Preset, 3–43
RGB, setting Gamut alarm, 3–33
RGB gamut, Diamond Display, 3–29
Rise time
calculating actual, 3–25
serial channel measurements, 3–24
RS232
connector pin assignments, B–1
rear panel overview, 2–7
S
Safety Certification Compliance, A–10
Safety Standards, A–10
Sample, selection using Line Select, 3–39
SAV Placement, Serial format checks, 3–48
SAV–EAV, in Configure WFM/VEC menu, 3–9
Saving, front panel settings as Preset, 3–43
Screen, filter part number, 1–2
SER A/B inputs, 2–7
SER ALARM, configuration menu, 3–11
SERIAL, 2–4
Serial A Input, Loop-through input, 2–7
SERIAL A/SERIAL B, 2–4
Serial Alarm, configure menu, 3–11
Serial B input, Loop-through input, 2–7
Serial channel measurements
aberrations, 3–23
amplitude, 3–22
jitter, 3–26
rise time, 3–24
word correlated behavior, 3–27
Serial format, 3–44
10/8 Bits, 3–46
ANC Checksum, 3–49
ANC Parity, 3–48
AP CRC ERR SEC, 3–46
APPROX CABLE LENGTH, 3–49
Approximate Cable Length for firmware V1.X, 3–47
Audio, 3–46
CABLE screen, 3–49
CABLE TYPE, 3–50
CABLE TYPE for firmware V1.X, 3–47
Changed Since Reset, 3–46
Data Range, 3–48
DISPLAY, 3–50
Display, 3–46
Elapsed Time, 3–46
F1 AP CRC Value, 3–46
F2 AP CRC Value, 3–46
FF CRC ERR SEC, 3–46
Field Length, 3–48
525/625 Lines, 3–46
Format Error, 3–46
FORMAT screen, 3–48
Line Length, 3–48
Other ANC Data, 3–46
RECEIVER POWER LEVEL, 3–49
Reset, 3–46
SAV Placement, 3–48
Serial Signal Level for firmware V1.X, 3–47
Signal Present, 3–46
SOURCE SIGNAL LEVEL, 3–49
STATUS screen, 3–45
STATUS screen for firmware V1.X, 3–47
Stuck Bits, 3–46
Serial readout screen
Cable, 3–49
Format, 3–48
Status, 3–45
Status for firmware V1.X, 3–47
Serial Signal Level, serial format for firmware V1.X,
3–47
Service manual, 1–3
Settings, saving as Preset, 3–43
1700F00 Cabinet, 1–6
1700F02 Portable cabinet, 1–6
1700F04 side-by-side rack mount assembly, 1–6
75 ohm terminator, 1–2
Shipping instrument, 1–10