Filter
Top Products
20
Public Switched Telephone Network (PSTN) Reporting
Settings for dial-up reporting using the telephone network are set in this area.
Account Number
The account number can be up to 10 digits long. The last four digits of
the account number will be used as the communicator’s account
number for 4x2 and CID format reports to the monitoring service.
✲ IMPORTANT! THE ACCOUNT NUMBER FIELD IS REQUIRED.
• SurGard System III - compatible SIA requires a 10-digit number
• PSTN/SIA requires a 6-digit number
• PSTN/CID and 4 by 2 requires a 4-digit number.
Enter the account number for the specifi c Console.
Reporting Format
Three Central Station PSTN reporting formats are available.
• Contact ID (CID)
• SIA
• 4 by 2
Contact ID is the default format. Select one of the other formats as
required by the Central Station.
Dialing Format
The default dialing format is DTMF tone dialing. If the telephone system
that the Console will be connected to does not support DTMF tone
dialing, select pulse dialing.
Dialing Tones Audible
By default dialing tones do not sound from the Console’s speaker. This
option is typically used for troubleshooting telephone issues.
Check this option box to have the Console speaker active during dialing.
Primary Telephone Number
The primary telephone number is the number that will be dialed fi rst
in the dialing sequence. The number can be up to 20 digits including
commas that each add a one second pause.
✲ IMPORTANT! THE PRIMARY TELEPHONE NUMBER FIELD IS REQUIRED.
Secondary Telephone Number
The secondary telephone number is the number that will be dialed
second in the dialing sequence if the primary number is unsuccessful.
The number can be up to 20 digits including commas that each add a
one second pause.
Split Reporting
The Console can report supervisory events to a supervisory telephone
number if split reporting is enabled. Split reporting is disabled by default.
When split reporting is enabled, reports for alarm events, reminder
message timeouts, activity window expirations, and 2-way audio calls are
made to the primary and secondary phone numbers.
Reports of home/away mode, Console trouble conditions, sensor trouble
conditions, and Automatic Status reports are made separately to the
supervisory phone number only.
Supervisory Telephone Number
The supervisory telephone number is the number that will be dialed to
report supervisory events if split reporting is enabled. The number can
be up to 20 digits including commas that each add a one second pause.
Internet Protocol (IP) Reporting
The PERS-4200 Console can be confi gured to communicate over-the-air
(OTA) using the optional add-on Model UMTS-3G Cellular Module. The
Module supports over-the-air data reporting for the PERS Console using 3G
and voice communications through the carrier’s cellular telephone network.
The settings for IP reporting using the cellular module are set in this area.
IP Account Number
The FIBRO IP reporting protocol allows up to 10 digits in the account
number. PERS truncates the left-most digits of the account number to fi t
the reporting format used. The cellular module adds left-most zeroes as
necessary for IP reporting. Enter the account number used for SurGard
IP reporting for the specifi c Console.
DNIS / Line #
DNIS is used by the Central station to help identify accounts. This allows
there to be multiple panels sending SIA/Contact ID events using account
1234 for example. The DNIS may be transmitted to the automation
software/printer to ID account 1234 as belonging to dealer X (DNIS
00001) and the other account 1234 as belong to dealer Y (DNIS of
00002). If it is not used it should be sent as all 0’s and it will not allow the
SIA/Contact ID account numbers to be extended.
FIBRO Heartbeat
Enter the time (in seconds) required by the Central Station receiver for
the FIBRO heartbeat. Default is 7200 seconds.
Linear Voice Gateway Management Timer
Enter the time (in minutes) for the periodic management connection
to the voice gateway, used for over-the-air confi guration update and
fi rmware download.
SIM ID
Displays the Subscriber Identity Module ID being used in the cellular module.
Central Station IP Address
The area is for entering the Central Station’s primary and secondary IP
address’, local port, and remote port numbers for the server that will be
receiving alarm reports from the Console. Enter the values required by
the server.
Voice Gateway
The area is for entering the Central Station’s voice gateway IP address
for the Linear Voice Gateway that will be handling voice-over-IP (VOIP)
communications from the Console during 2-way audio mode. Refer to the
Linear Voice Gateway instructions and settings for details.
IP Reporting Format
Three Central Station IP reporting formats are available.
• Surgard System III-compatible SIA
• Surgard System III-compatible CID18 Extended
• Surgard System III-compatible CID58 Extended
SURGARD SYSTEM III-COMPATIBLE CID18 EXTENDED
is the default
format. Select one of the other formats if required by the Central Station.
Cellular Network ID
Used to connect to a specifi c network. This specifi es the numeric
network identifi er, which is made from the Mobile Country Code (MCC)
and Mobile Network Code (MNC).
IP Service
The cellular service data network name string. For example: wap.cingular
or m2m.com.attz.
LEMI Ports
This area displays the name and fi rmware revision number of any option
modules connected to the Console.