Filter
Top Products
16
Annunciate Trouble Indication
With this option box checked, the Console will announce three system
trouble conditions if they occur: Console low battery, sensor low battery,
and no sensor status. Sensor troubles type are announced followed by the
sensor zone number. The default is to not annunciate these conditions.
✓ NOTE FOR UL APPLICATIONS: UL requires the Annunciation Trouble
Indication option to be enabled (option box checked).
Annunciate Status with Home Button
A short press of the HOME button will cause the Console to announce
the Console’s time, current mode, and any trouble conditions. The default
for status annunciations is enabled. Optionally, status annunciations can
be disabled by un-checking this option box.
Annunciate Phone-Line/AC Status
If the telephone line is disconnected, or the AC power to the Console
fails, the Console can annunciate these conditions. These annunciations
will clear when the condition is corrected.
The default sets these types of annunciations to ANNUNCIATE ONCE.
Alternately, use the this option to select OFF or ANNUNCIATE EVERY
HOUR. Regardless of this setting, the Console records the condition in
the event log and can report AC power failure to the monitoring service
(if AC reporting is enabled).
✓ NOTE: To prevent disturbing the subscriber, these annunciations will be
suppressed while the Console is in Night Mode
Clock Annunciation Format
Both 12-hour (AM/PM) and 24-hour (“military”) time formats are supported
in time announcements for Console status and reminder messages.
The default sets the time annunciations to 12-HOUR CLOCK format.
Alternately, use the this option to select 24-HOUR CLOCK format.
Data version
Displays the version number of the Console’s data for factory use and
troubleshooting.
Console Confi guration Misc.
Displays confi guration numbers of the Console for factory use and
troubleshooting.
Temperature Limit Settings
The Console contains a built-in sensor that constantly monitors the room
temperature. The system can report and annunciate if the current room
temperature measured is higher or lower than programmed temperature
limits.
The Console will announce the high or low temperature alert every minute
until the room temperature is within the programmed acceptable limits.
The temperature limit alert is enabled by default. Select DISABLE to turn
off this feature or select ENABLE HOME MODE ONLY to sound and
report temperature alerts only while the Console is in Home Mode.
The default set-point for the low-temp alert is 40°F (4.4°C).
The default set-point for the high-temp alert is 90°F (32.2°C).
To change the temperature set-points, enter new values (in Fahrenheit)
into the HIGH TEMP and/or LOW TEMP fi ll-in fi elds.
A TWO-WAY AUDIO check box is available to select if a temperature
alert starts a 2-way audio session with the monitoring station. The check
box is selected by default. Alternately, un-check this box to inhibit 2-way
audio after a temperature alert.
Language Selection
The Console can annunciate voice prompts in English or Spanish to guide
the user during operation, and guide the installer during programming.
The two resident languages in the Console are English (EN) and
Spanish (ES). Choose the active language for the Console using the
radio buttons in the Language Selection area.
To use a different language, the language vocabulary fi le must
fi rst be downloaded and installed in the Console’s fi rmware (See
Section 15.2).
Console Time Settings
The Console contains a built-in clock and calendar, and supports
automatic daylight saving time adjustment. The Console’s current time
and date setting and the daylight saving information is displayed on the
Console tab or the RA4200 software.
To change these settings, use the CONSOLE TIME function on the
COMMUNICATION menu (or press the CONSOLE TIME icon on the
toolbar ribbon). See Section 11.3.
✓ NOTE: If the UMTS-3G cellular module is installed, the Console’s time
will be set automatically over the air by the network.
Activity Windows
The activity timer is a feature that requires the subscriber to press the
Console’s HOME button or activate a activity reset transmitter during one
or two preset time windows to prevent an inactivity alarm from being
reported.
Two activity time windows can be set. Each time window can be enabled
or disabled, and has a start and stop time.
• To enable Activity Window 1 and/or Activity Window 2, check the enable
box next to the start and stop times.
• Set the start time for the activity window.
• Set the stop time for the activity window.
Night Mode
Night Mode is an option that will suspend all Console supervisory and
reminder annunciations during the Night Mode time window. This mode
allows the user to sleep without interruptions from the Console about
non-emergency conditions.
• To enable the Night Mode time window, check the enable box next to the
start and stop times.
• Set the start time for Night Mode.
• Set the stop time for Night Mode.