Filter
Top Products
13
Items Contents
RGB/COMPO. Sets the input signal of the INPUT A terminal to receive
RGB or component (COMPO.) signals.
(RGB p[COMPO.)
RGB : RGB signal is selected.
COMPO. : component signal is selected.
SCAN SIZE Sets the scan size when component (COMPO.) signals
are input to the INPUT A terminal.
(OVER p[UNDER)
OVER : standard scan size (95% overscan) is
selected.
UNDER : underscan size is selected.
ASPECT Sets the aspect ratio for INPUT B signals and INPUT A
component (480i, 480p) signals.
(4-3 p[ 16-9)
4-3 : sets the aspect ratio to 4:3. (Standard for INPUT B
signals.)
16-9 : sets the aspect ratio to 16:9. (Standard for INPUT A
component (480i, 480p) signals.)
COLOR SW Sets the color switch of the INPUT B signal input and the
INPUT A component (COMPO.) signal input.
(ONp[ OFF)
ON : usually keep COLOR SW set to ON (the picture is
colored).
OFF : the colored picture becomes black and white.
COLOR TEMP. Sets the color temperature to HIGH or LOW
(HIGH p[ LOW).
HIGH: sets the color temperature to HIGH.
LOW : sets the color temperature to LOW.
You can select (set) the display’s functions.
1 Press the MENU
MENU
button.
The <MAIN MENU> screen appears.
2 Press the SELECT
SELECT
button to select the
[FUNCTION SELECT] item.
The selection mark (
4
) moves to
the [FUNCTION SELECT] item.
3 Press the VOLUME/
ENTER
button.
The <FUNCTION SELECT> screen
appears.
4 Press the SELECT
SELECT
button to select
the desired adjustment
item.
The selection mark (
4
) moves to
the adjustment item.
5 Perform adjustment with the VOLUME/
ENTER
/ buttons.
* Items not displayed because of the selected input mode
(INPUT SELECT) cannot be adjusted.
<MAIN MENU> screen
<MAIN MENU> screen
<FUNCTION SELECT> screen
FUNCTION SELECTION (SETTING)
<FUNCTION SELECT> screen
• RGB/COMPO. : sets the input signal of the INPUT A terminal
• SCAN SIZE : sets the scan size
• ASPECT : sets the aspect ratio
• COLOR SW : sets the color switch
• COLOR TEMP.: sets the color temperature
Ⅵ RESETTING ITEMS TO THEIR FACTORY-SET (INITIAL)
VALUES
You can reset each item (RGB/COMPO., SCAN SIZE,
ASPECT COLOR SW and COLOR TEMP.) in the
<FUNCTION SELECT> menu to their factory-set (initial)
values.
1Select the [ reset] item in procedure 4.
2Press the VOLUME/ENTER
button.
The <reset> screen appears.
3Perform adjustment with the
VOLUME/ENTER button or
the MENU
MENU
button.
VOLUME/ENTER
button… Values are reset.
MENU
MENU
button… Reset is aborted
(values are unchanged).
* The screen from procedure 4 reappears.
6 After adjustment is complete, press the
MENU
MENU
button twice to exit the menu
screen.
Notes:
● The menu screen automatically disappears when no
operation is performed after about 30 seconds.
● When a prompt appears in the menu screen, it does not
disappear until the operation requested is performed.
● Before setting functions, make sure that signals are being
input to the monitor.
● Items that cannot be set or adjusted because of the
selected input mode (INPUT SELECT) are not displayed.
● When setting the [RGB/COMPO.] item, procedure 6 is not
needed. After being set, the picture temporarily disappears,
then the function selection is complete.
● The [SCAN SIZE] item can be set only when INPUT B
(NTSC composite or Y/C) signals or INPUT A component
signals are input.
● The [ASPECT] item can be set only when INPUT B signals
or INPUT A component signals (480i, 480p) are input. With
INPUT B signals, 4:3 (4-3) is the standard. With INPUT A
(COMPO.) signals, 16:9 (16-9) is the standard.
● The [COLOR SW] item can be set only when INPUT B
signals or INPUT A component signals are input.
● When the “
*
” mark appears after the [COLOR TEMP.]
setting is changed (HIGH or LOW), it means that the
[WHITE BALANCE] item in the <SET-UP MENU> screen
has been adjusted. [WHITE BALANCE] is different for
[HIGH] and [LOW].
p
p
<reset> screen
00.12.20, 0:39 PM13