Filter
Top Products
12
You can adjust the picture contrast, brightness, etc.
1 Press the MENU
MENU
button.
The <MAIN MENU> screen appears.
2 Press the SELECT
SELECT
button to select the
[PICTURE ADJ.] item.
The selection mark (
4
) moves to
the [PICTURE ADJ.] item.
3 Press the VOLUME/
ENTER
button.
The <PICTURE ADJ.> screen
appears.
4 Press the SELECT
SELECT
button to select
the desired adjustment
item.
The selection mark (
4
) moves to
the adjustment item.
5 Perform adjustment with the VOLUME/
ENTER
/ buttons.
*
Items not displayed because of the selected input mode
(INPUT SELECT) cannot be adjusted.
* Adjustable range: –20 — +20
PICTURE ADJUSTMENT
Items VOLUME/ENTER Contents
buttons
CONTRAST Contrast becomes lower
(–20 p +20)
Contrast becomes higher
(–20 [ +20)
BRIGHT Brightness becomes darker
(–20 p +20)
Brightness becomes brighter
(–20 [ +20)
CHROMA Chroma becomes lighter
(–20 p +20)
Chroma becomes deeper
(–20 [ +20)
PHASE Phase becomes more reddish
(–20 p +20)
Phase becomes more greenish
(–20 [ +20)
APERTURE Outline becomes more obscure
(–20 p +20)
Outline becomes clearer
(–20 [ +20)
Ⅵ SELECTING [ sub menu] IN PROCEDURE 4
You can also adjust items in procedure 5 with only the
selected item displayed. Use this if the full menu screen
makes it difficult to observe the monitor image.
1Select the [ sub menu] item in procedure 4.
2Press the VOLUME/
ENTER
button.
The <sub menu> screen appears.
(A single item is displayed at a
time.)
3Press the SELECT
SELECT
button to
select the desired item.
4Perform adjustment with the
VOLUME/ENTER /
buttons.
Ⅵ RESETTING ITEMS TO THEIR FACTORY-SET (INITIAL)
VALUES
You can reset the <PICTURE ADJ.> items to their factory-
set (initial) values.
1Select the [ reset] item in procedure 4.
2Press the VOLUME/ENTER
button.
The <reset> screen appears.
3Perform adjustment with the
VOLUME/ENTER button or
the MENU
MENU
button.
VOLUME/ENTER
button… Values are reset.
MENU
MENU
button… Reset is aborted
(values are unchanged).
* The screen from procedure 4 reappears.
6 After adjustment is complete, press the
MENU
MENU
button twice to exit the menu
screen.
Notes:
● The menu screen automatically disappears when no
operation is performed after about 30 seconds.
● When adjusting the picture, set each picture adjustment
knob on the front panel to the center position
(the knob clicks into place).
● It is possible to memorize the preset picture adjustment for
each video input (up to 3 inputs).
● Items not displayed because of the selected input mode
(INPUT SELECT) cannot be adjusted. In this case, it is also
impossible to perform adjustment with picture adjustment
knobs. (
⅜: adjustable –: not adjustable)
<sub menu> screen
HOW TO PERFORM MAIN MENU
ADJUSTMENTS
(cont’d.)
• CONTRAST: adjusts the picture contrast
• BRIGHT: adjusts the picture brightness
• CHROMA: adjusts the picture chroma
• PHASE: adjusts the picture phase
• APERTURE:adjusts the picture
aperture (outline)
INPUT SELECT Button
INPUT A INPUT B INPUT C
RGB COMPO. VIDEO RGB (PC)
CONTRAST ⅜⅜ ⅜ ⅜
BRIGHT ⅜⅜ ⅜ ⅜
CHROMA – ⅜⅜ –
PHASE – ⅜⅜ –
APERTURE – ⅜⅜ –
Picture
adjust-
ment
<reset> screen
<MAIN MENU> screen
<MAIN MENU> screen
<PICTURE ADJ.> screen
<PICTURE ADJ.> screen
( )
(
)
(
)
(
)
(
)
00.12.20, 0:39 PM12