Filter
Top Products
Flow Meter FC01-LQ Flow Meter FC01-LQ
50 Technical data 50 Technical data
8.3.1 Voltage output V1 - 5 V FS
Signal voltage range: U
S
= 0 V (1 V) to 5 V ±2% FS
Max. signal rippl: dU
S
= 5% FS
Min. admissible load resistance: R
l
= 1 kΩ
Max. admissible load capacity: C
l
= 1 nF
Max. admissible load inductance: L
l
= 100 nH
Short circuit proof: yes (XAO - between all terminals)
8.3.2 Voltage output V2 - 10 V FS
Signal voltage range: U
S
= 0 V (2 V) to 10 V ±2% FS
Max. signal ripple: dU
S
= 5% FS
Min. admissible load resistance: R
l
= 1 kΩ
Max. admissible load capacity: C
l
= 1 nF
Max. admissible load inductance: L
l
= 100 nH
Short circuit proof: yes (XAO - between all terminals)
8.3.3 Current output C1 - 20 mA FS
Signal current range: I
S
= 0 mA (4 mA) to 20 mA ±2% FS
Max. signal ripple: dI
S
= 5% FS
Min. admissible load resistance: R
l
= 0Ω
Max. admissible load resistance: R
l
= 250Ω
8.4 Signal outputs
The signal outputs are physically isolated from each other as well as from the electronic
control unit FC01-LQ.
8.4.1 Relay outputs R2 (DC or AC)
Pin selection: Signal name Pin XAH
Limit Switch 1 / shield 1
Limit Switch 1 / N/O 2
Limit Switch 1 / common 3
Limit Switch 1 / N/C 4
Limit Switch 2 / Schirm 5
Limit Switch 2 / N/O 6
Limit Switch 2 / common 7
Limit Switch 2 / N/C 8
8.3.1 Voltage output V1 - 5 V FS
Signal voltage range: U
S
= 0 V (1 V) to 5 V ±2% FS
Max. signal rippl: dU
S
= 5% FS
Min. admissible load resistance: R
l
= 1 kΩ
Max. admissible load capacity: C
l
= 1 nF
Max. admissible load inductance: L
l
= 100 nH
Short circuit proof: yes (XAO - between all terminals)
8.3.2 Voltage output V2 - 10 V FS
Signal voltage range: U
S
= 0 V (2 V) to 10 V ±2% FS
Max. signal ripple: dU
S
= 5% FS
Min. admissible load resistance: R
l
= 1 kΩ
Max. admissible load capacity: C
l
= 1 nF
Max. admissible load inductance: L
l
= 100 nH
Short circuit proof: yes (XAO - between all terminals)
8.3.3 Current output C1 - 20 mA FS
Signal current range: I
S
= 0 mA (4 mA) to 20 mA ±2% FS
Max. signal ripple: dI
S
= 5% FS
Min. admissible load resistance: R
l
= 0Ω
Max. admissible load resistance: R
l
= 250Ω
8.4 Signal outputs
The signal outputs are physically isolated from each other as well as from the electronic
control unit FC01-LQ.
8.4.1 Relay outputs R2 (DC or AC)
Pin selection: Signal name Pin XAH
Limit Switch 1 / shield 1
Limit Switch 1 / N/O 2
Limit Switch 1 / common 3
Limit Switch 1 / N/C 4
Limit Switch 2 / Schirm 5
Limit Switch 2 / N/O 6
Limit Switch 2 / common 7
Limit Switch 2 / N/C 8