Filter
Top Products
Flow Meter FC01-LQ Flow Meter FC01-LQ
18 Installation 18 Installation
XAO - - Analogue outputs
Connection by 8 pole connector; max. 1.5 mm
2
; LiYCY 2 x 0.25 mm
2
cable recommended
for each analogue output
Pin selection for analogue outputs (option: V1, V2, C1)
Pin No. Signal name Function
1 NC none
2 ANAO1 analogue output 1 - flow
3 ANA1GND reference potential for analogue output 1
4 SGNDA1 shield ground for analogue output 1 (ungrounded) *
5 SGNDA2 shield ground for analogue output 2 (ungrounded) *
6 ANAO2 analogue output 2 - temperature
7 ANA2GND reference potential for analogue output 2
8 NC none
* Apply shield on one side only.
XAH - Limit switch signal outputs - relay outputs - change over contacts
Connection by 8 pole connector; max. 1.5 mm
2
; LiYCY 3 x 0.38 mm
2
cable recommended
for each signal output
Pin No. Signal name Function
1 SGNDL1 shield ground 1
2 LIM1 non-inverted signal output 1 (N/O)
3 LIM1COM common change over input 1
4 /LIM1 inverted signal output 1 (N/C)
5 SGNDL2 shield ground 2
6 LIM2 non-inverted signal output 2 (N/O)
7 LIM2COM common change over input 2
8 /LIM2 inverted signal output 2 (N/C)
XAH - Limit switch signal outputs - transistor outputs NPN, freely connectable as emitter (-)
and collector (+) have been brought out separately.
Connection by 8 pole connector; max. 1.5 mm
2
; LifYCY 4 x 2 x 0.2 mm
2
cable recommended
Pin No. Signal name Function
1 /ERROR E summarized error indication - emitter terminal
2 /ERROR C summarized error indication - collector terminal
3 /BUSY/PULSE E availability signal or frequency output -
emitter terminal
4 /BUSY/PULSE C availability signal or frequency output -
collector terminal
XAO - Analogue outputs
Connection by 8 pole connector; max. 1.5 mm
2
; LiYCY 2 x 0.25 mm
2
cable recommended
for each analogue output
Pin selection for analogue outputs (option: V1, V2, C1)
Pin No. Signal name Function
1 NC none
2 ANAO1 analogue output 1 - flow
3 ANA1GND reference potential for analogue output 1
4 SGNDA1 shield ground for analogue output 1 (ungrounded) *
5 SGNDA2 shield ground for analogue output 2 (ungrounded) *
6 ANAO2 analogue output 2 - temperature
7 ANA2GND reference potential for analogue output 2
8 NC none
* Apply shield on one side only.
XAH - Limit switch signal outputs - relay outputs - change over contacts
Connection by 8 pole connector; max. 1.5 mm
2
; LiYCY 3 x 0.38 mm
2
cable recommended
for each signal output
Pin No. Signal name Function
1 SGNDL1 shield ground 1
2 LIM1 non-inverted signal output 1 (N/O)
3 LIM1COM common change over input 1
4 /LIM1 inverted signal output 1 (N/C)
5 SGNDL2 shield ground 2
6 LIM2 non-inverted signal output 2 (N/O)
7 LIM2COM common change over input 2
8 /LIM2 inverted signal output 2 (N/C)
XAH - Limit switch signal outputs - transistor outputs NPN, freely connectable as emitter (-)
and collector (+) have been brought out separately.
Connection by 8 pole connector; max. 1.5 mm
2
; LifYCY 4 x 2 x 0.2 mm
2
cable recommended
Pin No. Signal name Function
1 /ERROR E summarized error indication - emitter terminal
2 /ERROR C summarized error indication - collector terminal
3 /BUSY/PULSE E availability signal or frequency output -
emitter terminal
4 /BUSY/PULSE C availability signal or frequency output -
collector terminal