Filter
Top Products
18
Trigger
Trigger Function
Pressing the Shift Trigger key generates an immediate trigger
Trigger Control Functions
INIT:IMMED Initiate trigger immediately
INIT:CONT ON | OFF Initiate trigger continuously
TRIG:SOUR BUS | EXT
TTLT | IMM
Select transient trigger source
DELAY <value> Set trigger delay in seconds
ABORT Abort all trigger sequences
SYNC:SOUR PHASE | IMM Select synchronous trigger source
SYNC:PHASE <value> Set synchronous phase reference
Current
Current Functions
CURR:LEV <value> set immediate rms current limit
4
CURR:PEAK <value> set immediate peak current limit
3
CURR:PEAK:T <value> set triggered peak current limit
3
CURR:PEAK:M FIXED | STEP
PULSE | LIST
select the peak current limit mode
3
Voltage Functions
VOLT <value> set immediate ac output voltage
4
VOLT:T<value> set triggered output voltage
4
VOLT:M FIXED | STEP
PULSE | LIST
select the voltage mode
4
RANGE 150 | 300 set the voltage range
2, 4
OFFSET <value> set immediate dc offset voltage
3
OFFSET:T<value> set triggered dc offset voltage
3
OFFSET:M FIXED | STEP
PULSE | LIST
select the dc offset voltage mode
3
SLEW <value> set voltage slew in V/sec
4
SLEW:T<value> set triggered voltage slew in V/sec
4
SLEW:M FIXED | STEP
PULSE | LIST
select the voltage slew mode
4
OFF:SLW <value> set dc offset slew in V/sec
3
OFF:SLW:T<value> set triggered dc offset slew in V/sec
3
OFF:SLW:M FIXED | STEP
PULSE | LIST
select the dc offset voltage slew
mode
3
ALC INT | EXT select the voltage sense source
ALC:DET RTIME | RMS select the voltage sense detector
3
Phase
Phase Functions
PHASE <value> set immediate output phase
4
PHASE:T <value> set triggered output phase
4
PHASE:M FIXED | STEP
PULSE | LIST
select the phase mode
4
Freq Functions
FREQ <value> set immediate output frequency
FREQ:T<value> set triggered output frequency
FREQ:M FIXED | STEP
PULSE | LIST
select the frequency mode
SLEW <value> set frequency slew in Hz/sec
SLEW:T<value> set triggered frequency slew Hz/sec
SLEW:M FIXED | STEP
PULSE | LIST
select the frequency slew mode
Shape Functions
SHAPE SINE |SQUARE
CSIN | <user>
set immediate shape
SHAPE:T SINE |SQUARE
CSIN | <user>
set triggered shape
SHAPE:M FIXED | STEP
PULSE | LIST
set shape mode
CLIP <value> set clipping level
List
List Functions
COUNT <value> number of times a list repeats
DWEL:<index> <value> list of output dwell times
FREQ:<index> <value> list of output frequencies
FSLW:<index> <value> list of output frequency slew rates
IPK:<index> <value> list of output peak current limits
3
OFFS:<index> <value> list of dc output voltages
3
OSLW:<index> <value> dc offset voltage slew rate list
3
PHASE:<index> <value> list of output voltage phase
angles
4
SHAP:<index> SINE | SQUARE
CSIN | <user>
list of output waveform shapes
STEP ONCE | AUTO set response of list to triggers
TTLT:<index> ON | OFF set trigger out pulse list
VOLT:<index> <value> list of ac output voltages
4
VSLW:<index> <value> list of output voltage slew rates
4
Pulse Functions
WIDTH <value> set the pulse width
COUNT <value> set the number of output pulses
DCYCLE <value> set the pulse duty cycle
PER <value> set the pulse period count
HOLD WIDTH | DCYCLE set parameter that is held constant
Index Index
Index Functions
These are Shift Index keys which are used to scroll through indexed
functions. Press these keys to step through integers 0 through 50 for a
harmonic list, or 0 through 99 for list points. Hold down these keys to
rapidly access any harmonic or list point.
Functions
These keys let you move through the choices in a command list.
Command lists are circular; you can return to the starting position by
continuously pressing either key.
This key applies to 3-phase ac sources only.
Pressing this key successively selects phase 1
first, followed by phase 2, phase 3, and then all
three phases.
This key toggles the output on and off. When off,
the ac source output is disabled and the Dis
annunciator is on.
Trigger
Control
Voltage
Freq
Shape
Pulse
Phase
Select
Output
On/Off