Filter
Top Products
TIC-LF654L
2
Fluid conductivity:
3µS/cm minimum
Fluid temperature:
-4 to 248 °F
(
-
20 to +120 °C):
PFA lined flowmeter
-4 to 140 °F
(
-
20 to +60 °C):
Polyurethane lined flowmeter
23 to 176 °F
(
-
5to +80 °C):
Hard Rubber lined flowmeter
Ambient temperature:
-40 to 140 °F
(
-
40 to +60 °C):
PFA lined flowmeter
-4 to 140 °F (-20 to +60 °C):
PU lined and HR lined flowmeters
Structure:
Standard — IP 67 and NEMA 4X Watertight
Option — IP68 and NEMA 6P Submersible type
allows for accidental submergence up to 15m for
48 hours. This option is only available when PU
or HR liners are selected.
Power consumption:
Standard:10W(14VA)
at AC100V and Excitation current:0.2A
MAX:15W (22VA)
MAX:17W(24VA) with PROFIBUS
Approved hazardous location certifications:
Model: LF654/LF620F and LF654/LF622F
cFMus Nonincendive for use in
hazardous (classified) locations:
Class I, II, III, Division 2, Groups A-G
Detector and converter combination:
LF650/LF620: Combined type for standard
specification.
LF650/LF622: Separate type for standard
specification.
LF654/LF620F: Combined type with Ex approval of
Class I, II, III, Division 2 (cFMus).
LF654/LF622F: Separate type with Ex approval of
Class I, II, III, Division 2 (cFMus).
Mount-Anywhere Technology:
With TOSHIBA’s unique magnetic field
distribution technology the meter is highly immune
to upstream flow disturbances.
A minimum of 1D (one diameter) length of
upstream straight pipe from the flange is required to
maintain the specification performance.
Note: The test results were obtained and demonstrated at
TOSHIBA's flow calibration facility, Fuchu Japan.
Drinking water approvals:
PU and HR liner: NSF certified
Model LF654 Detector
Mounting style: Flange connection type
Fluid pressure:
-
15 psi or
-
1.0 bar
(
-
0.1 MPa) to the nominal
pressure of the connection flange.
Note: Before shipping from the manufacturer, each detector
unit is tested by the following test condition.
Pressure… twice of the pressure index number
(ex. 300 psi in case of ASME B 16.5 class 150 flange)
Time… 15 minutes
Connection flange standards:
ASME B16.5 class 150, ASME B16.5 class 300
EN1092-1 PN10, EN1092-1 PN16
JIS B 2220 10K, JIS B 2220 20K
Principal materials:
Case — carbon steel
Flange material — carbon steel
Linings —
1/2” to 18” (15 to 450mm): PFA
1/2” to 18” (15 to 450mm): PU
4” to 18” (100 to 450mm): HR
Note: PFA liners are mechanically retained for full vacuum
service (65 to 450 mm).
Electrodes —
Type-Super smooth, polished with self cleaning
finish, and non stick shape
316L stainless steel (std.) in case of PU and HR
lining
Hastelloy C equivalent (std.)
… in case of PFA lining
Note: Electrodes are mechanically buffed and
electro-chemically polished.
Grounding rings — 316 stainless steel (std.)
Note: See Table 4 for optional materials and other
related information.
Measuring tube material — 304 stainless steel
Terminal box material — ADC12(Aluminum
alloy die casting)
Coating: Polyurethane resin coating (std.) gray colored
Dimensions and weights: See Figure 3, 4, 5 and 6.
Cable connection port: for separate type detectors.
Cable gland —
LF650: Provided as standard, G 1/2 male screws.
LF654(with cFMus):Not provided, 3/4–14NPT
male screws are required.
Applicable diameter —
0.433 to 0.512 inch (11 to 13mm)