Filter
Top Products
38
Do not put the shaver back into the plugged-in Jet Clean System after
you have removed the rechargeable battery.
Do not connect the shaver to the mains again after you have removed
the rechargeable battery.
Guarantee and support
If you need information or support, please visit www.philips.com/
support or read the separate worldwide guarantee leafl et.
Guarantee restrictions
The shaving heads (cutters and guards) are not covered by the terms of
the international guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common problems you could
encounter with the appliance. If you are unable to solve the problem with
the information below, visit www.philips.com/support for a list of
frequently asked questions or contact the Consumer Care Centre in your
country.
Problem Possible cause Solution
The shaver does
not shave as well
as it used to.
The Jet Clean System has not
cleaned the shaver properly because
the cleaning fl uid in the cleaning
chamber is soiled or the cleaning
fl uid level is too low.
Clean the shaver thoroughly before you
continue shaving. If necessary, clean and
refi ll the cleaning chamber (see chapter
‘Cleaning and maintenance’).
The shaving heads are damaged or
worn.
Replace the shaving heads (see chapter
‘Replacing the shaving heads’).
Long hairs obstruct the shaving
heads.
Clean the shaving heads one by one (see
section ‘Cleaning the shaving unit with the
cleaning brush’ in chapter ‘Cleaning and
maintenance’).
You have not inserted the shaving
heads properly.
Make sure that the projections of the
shaving heads fi t exactly into the recesses
(see section ‘Cleaning the shaving unit with
the cleaning brush’).
The shaver does
not work when I
press the on/off
button.
The rechargeable battery is empty. Recharge the battery (see chapter
‘Charging’) or connect the shaver to the
mains.
The temperature of the shaver is too
high. In this case, the shaver does not
work.
As soon as the temperature of the shaver
has dropped suffi ciently, you can switch on
the shaver again.
The shaver is not
entirely clean after
I clean it in the Jet
Clean System.
The cleaning fl uid in the cleaning
chamber is soiled.
Empty and rinse the cleaning chamber (see
section ‘Cleaning the shaving unit in the
Jet Clean System’ in chapter ‘Cleaning and
maintenance’).
Problem Possible cause Solution
The cleaning fl uid level is too low.
If the fl uid volume in the cleaning
chamber drops below the minimum
level during the cleaning program,
the program aborts.The cleaning
symbol and the ‘fl uid low’ symbol
fl ash at intervals and the holder
returns to its starting position.
Refi ll the cleaning chamber with cleaning
fl uid up to the MAX level (see section
‘Cleaning the shaving unit in the Jet
Clean System’ in chapter ‘Cleaning and
maintenance’).
You have used another cleaning fl uid
than the original Philips cleaning fl uid.
Only use Jet Clean solution HQ200.
You have not closed the locking lever
of the Jet Clean System properly,
or you have not placed the shaver
in the Jet Clean Shaver properly. In
these cases the Jet Clean System
starts to operate, but the cleaning
program is not performed properly.
Place the shaver without protection cap in
the Jet Clean System properly. Close the
locking lever properly.
The Jet Clean
System does not
work when I press
the on/off button.
The Jet Clean System is not
connected to the mains.
Put the small plug in the Jet Clean System
and put the adapter in the wall socket.
Water leaks from
the shaver after
cleaning.
This is normal and not dangerous. During rinsing some water may collect
between the power unit and the housing.
After rinsing this water fl ows out through
the socket. The power unit is completely
watertight so water cannot reach the
electronic parts of the shaver. Your shaver
continues to be absolutely safe.
ENGLISH ENGLISH
Do not put the shaver back into the plugged-in Jet Clean System after
you have removed the rechargeable battery.
Do not connect the shaver to the mains again after you have removed
the rechargeable battery.
Guarantee and support
If you need information or support, please visit www.philips.com/
support or read the separate worldwide guarantee leafl et.
Guarantee restrictions
The shaving heads (cutters and guards) are not covered by the terms of
the international guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common problems you could
encounter with the appliance. If you are unable to solve the problem with
the information below, visit www.philips.com/support for a list of
frequently asked questions or contact the Consumer Care Centre in your
country.
Problem Possible cause Solution
The shaver does
not shave as well
as it used to.
The Jet Clean System has not
cleaned the shaver properly because
the cleaning fl uid in the cleaning
chamber is soiled or the cleaning
fl uid level is too low.
Clean the shaver thoroughly before you
continue shaving. If necessary, clean and
refi ll the cleaning chamber (see chapter
‘Cleaning and maintenance’).
The shaving heads are damaged or
worn.
Replace the shaving heads (see chapter
‘Replacing the shaving heads’).
Long hairs obstruct the shaving
heads.
Clean the shaving heads one by one (see
section ‘Cleaning the shaving unit with the
cleaning brush’ in chapter ‘Cleaning and
maintenance’).
You have not inserted the shaving
heads properly.
Make sure that the projections of the
shaving heads fi t exactly into the recesses
(see section ‘Cleaning the shaving unit with
the cleaning brush’).
The shaver does
not work when I
press the on/off
button.
The rechargeable battery is empty. Recharge the battery (see chapter
‘Charging’) or connect the shaver to the
mains.
The temperature of the shaver is too
high. In this case, the shaver does not
work.
As soon as the temperature of the shaver
has dropped suffi ciently, you can switch on
the shaver again.
The shaver is not
entirely clean after
I clean it in the Jet
Clean System.
The cleaning fl uid in the cleaning
chamber is soiled.
Empty and rinse the cleaning chamber (see
section ‘Cleaning the shaving unit in the
Jet Clean System’ in chapter ‘Cleaning and
maintenance’).
Problem Possible cause Solution
The cleaning fl uid level is too low.
If the fl uid volume in the cleaning
chamber drops below the minimum
level during the cleaning program,
the program aborts.The cleaning
symbol and the ‘fl uid low’ symbol
fl ash at intervals and the holder
returns to its starting position.
Refi ll the cleaning chamber with cleaning
fl uid up to the MAX level (see section
‘Cleaning the shaving unit in the Jet
Clean System’ in chapter ‘Cleaning and
maintenance’).
You have used another cleaning fl uid
than the original Philips cleaning fl uid.
Only use Jet Clean solution HQ200.
You have not closed the locking lever
of the Jet Clean System properly,
or you have not placed the shaver
in the Jet Clean Shaver properly. In
these cases the Jet Clean System
starts to operate, but the cleaning
program is not performed properly.
Place the shaver without protection cap in
the Jet Clean System properly. Close the
locking lever properly.
The Jet Clean
System does not
work when I press
the on/off button.
The Jet Clean System is not
connected to the mains.
Put the small plug in the Jet Clean System
and put the adapter in the wall socket.
Water leaks from
the shaver after
cleaning.
This is normal and not dangerous. During rinsing some water may collect
between the power unit and the housing.
After rinsing this water fl ows out through
the socket. The power unit is completely
watertight so water cannot reach the
electronic parts of the shaver. Your shaver
continues to be absolutely safe.
ENGLISH ENGLISH
PT729CC_A6_CS3.indd 38 13.4.26 2:47:22 PM