Filter
Top Products
36
5 Turn the lock anticlockwise (A) and remove the retaining frame (B).
6 Remove the shaving heads and place new ones in the shaving unit.
Note: Make sure that the projections of the shaving heads fi t exactly into the
recesses.
7 Put the retaining frame back into the shaving unit and turn the lock
clockwise.
8 Insert the lug of the new shaving unit into the slot in the top of the
shaver. Then close the shaving unit.
Note: If the shaving unit does not close smoothly, check if you have inserted
the shaving heads properly and if the retaining frame is locked.
9 Press and hold the on/off button for 5 seconds to reset . The orange
light will go out.
Accessories
To retain the top performance of your shaver, make sure you clean it
regularly and replace its shaving heads at the recommended time.
Shaving heads
A
B
5 sec.
- We advise you to replace your shaving heads every two years. Always
replace them with HQ8 Philips Shaving Heads.
Cleaning
Use Jet Clean solution (HQ200) for regular cleaning of the shaving -
heads.
Use Cleaning spray (HQ110) to clean the shaving heads thoroughly. -
Environment
- Do not throw away the shaver and the Jet Clean System with the
normal household waste at the end of their life, but hand them in at an
offi cial collection point for recycling. By doing this, you help to preserve
the environment.
- The built-in rechargeable shaver battery contains substances that
may pollute the environment. Always remove the battery before you
discard or hand in the shaver at an offi cial collection point. Dispose
of the battery at an offi cial collection point for batteries. If you have
trouble removing the battery, you can also take the appliance to a
Philips service centre. The staff of this centre will remove the battery
for you and will dispose of it in an environmentally safe way.
Removing the rechargeable shaver battery
Only remove the rechargeable battery when you discard the shaver.
Make sure the rechargeable battery is completely empty when you
remove it.
1 Disconnect the shaver from the mains, remove it from the Jet Clean
System.
2 Let the shaver run until it stops.
3 Undo the screws in the back of the shaver and in the hair chamber.
4 Remove the front panel and the back panel.
5 Bend the 6 hooks aside and take out the power unit.
Be careful, the hooks are sharp.
6 Remove the battery.
Be careful, the battery strips are sharp.
ENGLISH ENGLISH
5 Turn the lock anticlockwise (A) and remove the retaining frame (B).
6 Remove the shaving heads and place new ones in the shaving unit.
Note: Make sure that the projections of the shaving heads fi t exactly into the
recesses.
7 Put the retaining frame back into the shaving unit and turn the lock
clockwise.
8 Insert the lug of the new shaving unit into the slot in the top of the
shaver. Then close the shaving unit.
Note: If the shaving unit does not close smoothly, check if you have inserted
the shaving heads properly and if the retaining frame is locked.
9 Press and hold the on/off button for 5 seconds to reset . The orange
light will go out.
Accessories
To retain the top performance of your shaver, make sure you clean it
regularly and replace its shaving heads at the recommended time.
Shaving heads
A
B
5 sec.
- We advise you to replace your shaving heads every two years. Always
replace them with HQ8 Philips Shaving Heads.
Cleaning
Use Jet Clean solution (HQ200) for regular cleaning of the shaving -
heads.
Use Cleaning spray (HQ110) to clean the shaving heads thoroughly. -
Environment
- Do not throw away the shaver and the Jet Clean System with the
normal household waste at the end of their life, but hand them in at an
offi cial collection point for recycling. By doing this, you help to preserve
the environment.
- The built-in rechargeable shaver battery contains substances that
may pollute the environment. Always remove the battery before you
discard or hand in the shaver at an offi cial collection point. Dispose
of the battery at an offi cial collection point for batteries. If you have
trouble removing the battery, you can also take the appliance to a
Philips service centre. The staff of this centre will remove the battery
for you and will dispose of it in an environmentally safe way.
Removing the rechargeable shaver battery
Only remove the rechargeable battery when you discard the shaver.
Make sure the rechargeable battery is completely empty when you
remove it.
1 Disconnect the shaver from the mains, remove it from the Jet Clean
System.
2 Let the shaver run until it stops.
3 Undo the screws in the back of the shaver and in the hair chamber.
4 Remove the front panel and the back panel.
5 Bend the 6 hooks aside and take out the power unit.
Be careful, the hooks are sharp.
6 Remove the battery.
Be careful, the battery strips are sharp.
ENGLISH ENGLISH
PT729CC_A6_CS3.indd 36 13.4.26 2:47:22 PM