Filter
Top Products
30
5 To remove the shaver from the Jet Clean System, move the locking
lever upwards until it does not go any further and remove the shaver.
Using the shaver
Note: You can also use the appliance directly from the mains. Simply connect
the shaver to the mains.
Shaving
1 Press the on/off button once to switch on the shaver.
2 Move the shaving heads over your skin. Make circular movements.
Your skin may need 2 or 3 weeks to get accustomed to the Philips -
shaving system.
3 Press the on/off button once to switch off the shaver.
4 Clean the shaver (see chapter ‘Cleaning and maintenance’).
Cleaning and maintenance
Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the shaver and the
Jet Clean System.
The best and most hygienic way to clean the shaver is in the Jet Clean -
System. You can also rinse the shaver under the tap or clean it with the
cleaning brush supplied.
Clean the shaver after every shave for optimal shaving performance. -
Regular cleaning guarantees better shaving performance. -
For the best cleaning results, we advise you to use the Philips Cleaning -
spray (HQ110) and the Jet Clean solution (HQ200).
Be careful with hot water. Always check if the water is not too hot, to -
prevent your hands from getting burnt.
Note: Water may leak from the socket at the bottom of the shaver when you
rinse it. This is normal and not dangerous because all electronics are enclosed
in a sealed power unit inside the shaver.
Cleaning the shaving unit under the tap
1 Switch off the shaver and disconnect it from the mains.
2 Press the release button to open the shaving unit.
3 Rinse the shaving unit and hair chamber under a hot tap for 30
seconds.
Be careful with hot water. Always check if the water is not too hot, to
prevent your hands from getting burnt.
- Rinse the hair chamber and the inside of the shaving unit.
- Rinse the outside of the shaving unit.
4 Close the shaving unit and shake off excess water.
Be careful not to hit the shaving unit against anything while shaking off
excess water.
Never dry the shaving unit and the hair chamber with a towel or tissue,
as this may damage the shaving heads and the coupling spindles.
5 Open the shaving unit again and leave it open to let the shaver dry
completely.
Cleaning the shaving unit with the cleaning brush
1 Switch off the shaver and disconnect it from the mains.
2 Press the release button to open the shaving unit.
3 Pull the shaving unit off the shaver.
ENGLISH ENGLISH
5 To remove the shaver from the Jet Clean System, move the locking
lever upwards until it does not go any further and remove the shaver.
Using the shaver
Note: You can also use the appliance directly from the mains. Simply connect
the shaver to the mains.
Shaving
1 Press the on/off button once to switch on the shaver.
2 Move the shaving heads over your skin. Make circular movements.
Your skin may need 2 or 3 weeks to get accustomed to the Philips -
shaving system.
3 Press the on/off button once to switch off the shaver.
4 Clean the shaver (see chapter ‘Cleaning and maintenance’).
Cleaning and maintenance
Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol or acetone to clean the shaver and the
Jet Clean System.
The best and most hygienic way to clean the shaver is in the Jet Clean -
System. You can also rinse the shaver under the tap or clean it with the
cleaning brush supplied.
Clean the shaver after every shave for optimal shaving performance. -
Regular cleaning guarantees better shaving performance. -
For the best cleaning results, we advise you to use the Philips Cleaning -
spray (HQ110) and the Jet Clean solution (HQ200).
Be careful with hot water. Always check if the water is not too hot, to -
prevent your hands from getting burnt.
Note: Water may leak from the socket at the bottom of the shaver when you
rinse it. This is normal and not dangerous because all electronics are enclosed
in a sealed power unit inside the shaver.
Cleaning the shaving unit under the tap
1 Switch off the shaver and disconnect it from the mains.
2 Press the release button to open the shaving unit.
3 Rinse the shaving unit and hair chamber under a hot tap for 30
seconds.
Be careful with hot water. Always check if the water is not too hot, to
prevent your hands from getting burnt.
- Rinse the hair chamber and the inside of the shaving unit.
- Rinse the outside of the shaving unit.
4 Close the shaving unit and shake off excess water.
Be careful not to hit the shaving unit against anything while shaking off
excess water.
Never dry the shaving unit and the hair chamber with a towel or tissue,
as this may damage the shaving heads and the coupling spindles.
5 Open the shaving unit again and leave it open to let the shaver dry
completely.
Cleaning the shaving unit with the cleaning brush
1 Switch off the shaver and disconnect it from the mains.
2 Press the release button to open the shaving unit.
3 Pull the shaving unit off the shaver.
ENGLISH ENGLISH
PT729CC_A6_CS3.indd 30 13.4.26 2:47:18 PM