Filter
Top Products
–12–
STANDARD PROGRAMMING
RECORD A VOICE MESSAGE
You must record a message and program at least one phone number in
order for the Dial Alert to work.
The voice recording procedure is different between the 2 operating modes,
SC-001 Mode and Sensor Mode.
To record a voice message under SC-001 Mode:
1. Enter the current password (factory default password is 0000), then press
[PROG], display will show [P] meaning you are now in programming mode.
2. Enter [3] which represents voice recording. You will see [P3 0 40]. The
number on the most right represents the voice recording duration. 40
means 40 seconds.
3. To start recording, press [ ] button. You now can start to record the
voice message. The number 40 will decrease and voice recording will stop
when it reaches 0. You may also press [ ] at anytime to stop the voice
recording.
4. After recording the message, you will hear the recorded message. After
the message playback, it will quit from programming and return to
standby mode.
5. The display still shows “not rEAdy” because no phone number has been
programmed.
To record a voice message under Sensor Mode:
1. Enter the current password (factory default password is 0000), then press
[PROG], display will show [P] meaning you are now in programming mode.
2. Enter [3] which represents voice recording. You will see [P3 0 09]. The
number following P3 is the message number, 0 is the primary message
(max 9 seconds) and 1 to 6 represent messages 1 to 6, each can be 5
seconds. The most right digits represents the voice recording duration,
09 mean 9 seconds.
3. Enter [0] to [6] to select which message you would like to record. If you
enter [3], you should see [P3 3 05].
Note: remember what message you record to each recording, when you
program a sensor later on, you can select which message you want it to
playback.
4. To start recording, press [ ] button. You now can start to record the voice
message. The number will decrease and voice recording will stop when it
reaches 0. You may also press [ ] at anytime to stop the voice recording.
–13–
STANDARD PROGRAMMING
5. After recording the message, you will hear the recorded message. After the
message playback, it will quit from programming and return to standby mode.
6. The display still shows “not rEAdy” because no phone number has been
programmed.
MESSAGE PLAYBACK
If you would like to listen to the recorded message, you can playback the
message by following the instructions below.
1. Enter the current password (factory default password is 0000 ), then
press [ ], then press [3], display will show [L3] meaning you are now
in voice message playback mode.
2. Enter the number that represents which message you want to playback:
0 - Main Message 4 - Zone 4 Message
1 - Zone 1 Message 5 - Zone 5 Message
2 - Zone 2 Message 6 - Zone 6 Message
3 - Zone 3 Message
3. Display now shows something like [L3 1 05] where the last 2 digits
represent the duration of the voice message you have recorded. Press
[ ] will playback the recorded message.
PROGRAM A PHONE NUMBER
You may program up to 9 different phone numbers. Follow the instructions
below to program phone numbers.
1. Enter the current password (factory default password is 0000 ), then press
[PROG], display will show [P] meaning you are now in programming mode.
2. Enter [4] which represents phone number programming. You will see [P4
PHonE 1]. The number on the most right represents the phone number,
from Phone 1 to Phone 9.
3. Select the phone number you would like to program, from 1 - 9, then press [ ].
4. Enter the phone number, then press [ ].
5. Display will show [rEdIAL 2], this is the default redial count. Press [ ]
to accept, or enter a value from 1 - 2 to change the setting. Redial count
is how many times this phone number will be retried if it is busy.
6. Display will show [rEPEAt 3], this is how many times the voice message
will be played. Press [ ] to accept 3 times, or enter a value from 1 - 9
to change the setting.
Note:
Skylink recommends that the telephone or pager numbers of your relatives,
neighbors, office/work, friends or doctor be programmed into your Dial-Alert.