Invacare Ranger IIJR Wheelchair User Manual


 
54
B. WHEELCHAIR NOT EQUIPPED WITH FLIP-UP
REMOVABLE FOOTBOARD - Remove the front
hex screw that secures the existing left battery
tray bracket to the wheelchair frame.
4. Remove the locknut that secures existing left battery
tray hanger bracket and MKIV controller from the
wheelchair.
5. Remove the existing left battery tray hanger bracket
from the wheelchair.
6. Line up the mounting holes in the new battery tray
hanger bracket with the front mounting hole and rear
stud on the wheelchair frame.
7. Perform one (1) of the following:
A. WHEELCHAIR EQUIPPED WITH FLIP-UP RE-
MOVABLE FOOTBOARD - Reinstall the hex
screw and spacer that secures the new left bat-
tery tray hanger bracket and footboard mounting
bracket to the wheelchair frame. Use Loctite 242
and torque to 156-in/lbs.
B. WHEELCHAIR NOT EQUIPPED WITH FLIP-
UP REMOVABLE FOOTBOARD - Reinstall the
front hex screw that secures the new left battery
tray hanger bracket to the wheelchair frame. Use
Loctite 242 and torque to 156-in/lbs.
8. Reinstall locknut. Use Loctite 242 and torque to 156-
in/lbs.
9. Torque the rear locknut that secures MKIV controller to
the wheelchair to 156-in/lbs.
FOR MODEL R2
JR
(FIGURE 15).
NOTE: Right and left is determined by sitting in wheel-
chair.
1. Remove the footrests. Refer to INSTALLING /RE-
MOVING FOOTRESTS in PROCEDURE 3 of the
Owner's Manual, part number 1080722.
2. Remove the battery boxes from the wheelchair. Refer
to
INSTALLING/REMOVING BATTERY BOXES in this
procedure of the manual.
3. Remove the battery tray. Refer to
REMOVING BAT-
TERY TRAY in this procedure of the manual.
4. Remove the two (2) mounting screws that secures
the existing right battery tray hanger bracket to
wheelchair frame.
5. Secure NEW battery tray hanger bracket to wheel-
chair frame with the existing two (2) mounting
screws. Securely tighten.
6. Reinstall battery tray, battery boxes, and footrests
by reversing STEPS 1-3.
FIGURE 15 - REPLACING RIGHT BATTERY TRAY
HANGER BRACKET FOR MODEL R2
JR
Battery Tray
Hanger Bracket
Mounting Screws
Wheelchair
Frame
FIGURE 16 - REPLACING LEFT BATTERY TRAY
HANGER BRACKET FOR MODELS R2
BASIC
AND
R2
STANDARD
MKIV
Controller
Rear Locknut - Loosen,
but Do Not Remove
Locknut
Battery Tray Hanger Bracket
Footboard
Mounting
Bracket
Hex Screw
Spacer
Wheelchair
Frame
F
W
D
W
H
E
E
L
C
H
A
I
R
S
Replacing Left Battery Tray Hanger Bracket
FOR MODELS R2
BASIC
AND R2
STANDARD
(FIGURE 16).
NOTE: Right and left is determined by sitting in wheel-
chair.
1. Remove the battery boxes from the wheelchair. Re-
fer to
INSTALLING/REMOVING BATTERY BOXES
in this procedure of the manual.
2. Loosen, but do not remove the rear locknut that se-
cures MKIV controller to the wheelchair.
3. Perform one (1) of the following:
A. WHEELCHAIR EQUIPPED WITH FLIP-UP RE-
MOVABLE FOOTBOARD - Remove the hex
screw and spacer that secures the existing left
battery tray hanger bracket and footboard mount-
ing bracket to the wheelchair frame.
F
W
D
W
H
E
E
L
C
H
A
I
R
S
PROCEDURE 13 FWD WHEELCHAIRS