Filter
Top Products
102841 Rev. A
14
ENGLISH
IX.
D. HEIGHT ADJUSTABLE ARMRESTS (Figure 7)
1. Installation
a. Slide the outer armpost into the receiver mounted to the wheelchair frame.
b.
The armrest will automatically lock into place.
2. Height Adjustment
a. Rotate release lever to second stop.
b.
Slide armrest pad up or down to desired height.
c. Return lever to locked position against armpost.
d. Push arm pad until upper armpost locks firmly into place.
3. Removing Armrest
a. Rotate release lever to first stop and remove the armrest.
4. Replacing Armrest
a. Slide armrest back into receiver.
b. Return release lever to locked position
against armpost.
5. Adjusting Armrest Receiver Fit
To tighten or loosen the fit of the outer armpost in the receiver:
a. Loosen the four receiver adjustment bolts on the sides of the receiver.
b. With the armrest in the receiver, squeeze the receiver to achieve the desired fit.
c. Tighten the four bolts.
6. Adjusting Inner Armpost Fit
a. Two set screws are installed in the outer armpost.
b. Turn the set screws in or out until the desired fit is achieved.
7. Position Adjustment
a. Loosen the three clamp bolts until clamp is loose.
b. Slide armrest receiver to desired position.
c. Tighten all 3 bolts to 212in.-lbs. (24 Nm).
E. BACK ANGLE ADJUSTMENT (Figures 8 & 9)
Adjusting the Back Angle
1. Using a 4mm Allen Key and 10mm wrench on opposite side completely remove the
pivot screw (A) that attaches the back tube (C) to angle adjustable backrest bracket
(B).
2. For folding back, loosen but don’t remove cam stop (D) using a 4mm Allen Key and
wrench. For non folding back, loosen but don’t remove 6mm socket screw (E) and
loosen but don’t remove both lower 6mm button head screws (F)
3. Determine new angle by aligning the upper hole in the backrest tube (C) with the dif-
ferent holes in the backrest bracket (B).
4. Once proper hole is determined, while aligning hole in one end of the pivot washer
with proper hole, insert pivot screw (A) through proper hole in outside wall of back-
rest bracket (B) and through the hole in pivot washer. Continue to feed screw through
both walls of backrest tube (C). W
rap pivot washer around front of backrest tube and
align remaining hole in pivot washer with proper hole on the inner wall of backrest
bracket (B).
5.
Once in place using a 4mm Allen Key and 10mm wrench tighten the pivot screw (A)
back into place.
NOTE– F
or folding back, do not over tighten. Backrest must be allowed to fold easily
.
6. Repeat procedure to the other side of the wheelchair.
7. Adjust and tighten cam stops for both sides of the wheelchair (D), see steps below for
folding back. For non folding back tighten 6mm socket screw (E) and tighten 6mm
button head screws (F) back into place.
CA
UTION –
When changing the back angle of the wheelchair both the left and right angle adjustable back
bracket must be in the same hole position (see steps 3 &4) before the wheelchair is to be used.
9Non-Folding Back
8
A
B
E
F
F
C
D
Height-Adjustable
Armrest Key
1. Outer armpost
2. Standard receiver
3.
Release lever
4. Armrest pad
5. Transfer bar
6.
Side panel
7. Outer armpost tension
adjustment set screws
8. Inner armpost
9. Receiver adjustment bolts
10.Release Lever
11.Clamp bolts
1
10
11
6
7
8
4
3
5
9
2
7