Filter
Top Products
Braun Corporation FMVSS No. 403 Quick Reference Installation Sheet 31312 Rev. A
Proper maintenance is necessary to ensure
safe, troublefree operation. Inspecting the lift for
any wear, damage or other abnormal conditions
should be a part of your daily routine. Simple
inspections can detect potential problems.
The maintenance and lubrication procedures
specied in this schedule must be performed
by a Braun authorized service representative at
the scheduled intervals according to the number
of cycles. NHTSA NV05/NMV05 Series lifts are
equipped with 2 cycle counters (1 display built into
the control board and 1 located in the cover).
The NV05/NMV05 is equipped with hardened pins
and self-lubricating bushings to decrease wear,
provide smooth operation and extend the service
life of the lift.
When servicing the lift at the recommended inter-
vals, inspection and lubrication procedures speci-
ed in the previous sections should be repeated.
Clean the components and the surrounding area
before applying lubricants. LPS2 General
Purpose Penetrating Oil is recommended where
Light Oil is called out. Use of improper lubricants
can attract dirt or other contaminants which could
result in wear or damage to the components.
Platform components exposed to contaminants
when lowered to the ground may require extra
attention.
Lift components requiring grease are lubricated
during assembly
procedures. When
these components
are replaced, grease
must be applied dur-
ing installation pro-
cedures. Specied
lubricants are avail-
able from The Braun
Corporation (part
numbers provided
below).
All listed inspec-
tion, lubrication and
maintenance procedures should be repeated at “750
cycle” intervals following the scheduled “4500 Cycles”
maintenance. These intervals are a general guideline
for scheduling maintenance procedures and will vary
according to lift use and conditions. Lifts exposed to
severe conditions (weather, environment, contamina-
tion, heavy usage, etc.) may require inspection and
maintenance procedures to be performed more often
than specied.
Discontinue lift use immediately if maintenance
and lubrication procedures are not properly per-
formed, or if there is any sign of wear, damage or im-
proper operation. Contact your sales representative
or call The Braun Corporation at 1-800-THE LIFT
®
.
One of our national Product Support representatives
will direct you to an authorized service technician who
will inspect your lift.
W
A
RNING
Maintenance and lu-
brication procedures
must be performed
as specied by an
authorized service
technician. Failure
to do so may result
in serious bodily
injury and/or prop-
erty damage.
750
Cycles
Apply Light Grease - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Grease - See Lubrication Diagram
Apply Light Grease - See Lubrication Diagram
Tighten, repair or replace if needed.
Tighten, resecure or replace if needed.
Resecure, replace damaged parts or otherwise
correct as needed. Note: Apply lubricant during
reassembly procedures.
Perform all procedures listed in previous section also
1500
Cycles
Apply Light Grease - See Lubrication Diagram
Add Lucas Heavy Duty Oil Stabilizer
4500
Cycles
Perform all procedures listed in previous sections also
Repeat all previously listed inspection, lubrica-
tion and maintenance procedures at 750 cycle
intervals.
Consecutive
750 Cycle
Intervals
Platform fold mechanism
Ballscrew / main drive
Clean ground cable at battery and frame
Check power cables
Maintenance and Lubrication
Downstop pivot points (2)
Upper lift rod pin
Lower lift rod pin
Kickout spring (located in switch arm)
Platform hinges (6)
Outboard barrier latch
Inboard locator latch mechanism
Check mounting hardware
Check all fasteners (snap rings, nuts, hairpins, etc.)
Check all pivot points for excessive wear
Specied (recommended) Available Braun
Lubricant Type Lubricant Amount Part No.
LO - Light Oil
DE - Door-Ease
Light Grease Lubriplate 14 oz.
naC )esoprupitluM(
LG - Light Grease
15807
15806
15805
Light Penetrating Oil LPS2, General Purpose 11 oz.
(30 weight or equivalent) Penetrating Oil Aerosol Can
Stainless Stick Door-Ease 1.68 oz.
)ebut( kcitS )ebut( elytS
OS - Oil Stabilizer
77000-000
.tq 1 ytuD yvaeH sacuL liO
reniatnoC rezilibatS liO rezilibatS
Kickout Spring
(hidden)
LO
Main Drive Ballscrew
(in Frame Tube - hidden)
OS
Upper Lift
Rod Pin
LO
Downstop Pivot Points
(hidden)
LG
Platform Fold
Mechanism
(Under Cover)
LG
Inboard Locator
Latch Mechanism
LG
Platform
Hinges (6)
LO
Outer Barrier Latch
Lower Lift
Rod Pin
LO