Braun 5 Mobility Aid User Manual


  Open as PDF
of 32
 
Page 11
57 – Outer barrier is not up and latched and
ground detect switch did not deactivate (Century
and Vista only)
58 – Outer barrier is not up and latched and the plat-
form is 3” above the ground
59 – Outer barrier is not up after pausing platform
travel
60 – The kickout gas springs are worn, replace before
using
75 – Low voltage detected; must turn off power switch
WRUHVHW/&'
77 – Vehicle secure interlock has not been activated
90 – Position will be set if you keep holding the button
until it beeps
91 – Position is out of a predetermined acceptable
UDQJHRIÁRRUSRVLWLRQ
92 – Bridge switch is not made, needs adjusting
93 – Inner rollstop occupied switch is not made,
position needs to be moved or switch should be
adjusted
²2XWHUEDUULHULVQRWPDGHÀ[DQGWU\DJDLQ
95 – Outer barrier latch is not made (check for jumper
on Century and Vista lifts, check latch on Millen-
nium lifts)
99 – Controller program is not valid; replace controller
)ODVKLQJ1XPEHUV
)ODVKLQJ²8QIROGEXWWRQLVSUHVVHG
)ODVKLQJ²)ROGEXWWRQLVSUHVVHG
)ODVKLQJ²'RZQEXWWRQLVSUHVVHG
)ODVKLQJ²8SEXWWRQLVSUHVVHG
)ODVKLQJ²%ULGJHVZLWFKLVDFWLYDWHG
)ODVKLQJ²2XWHUEDUULHUODWFKVZLWFKLVDFWLYDWHG
)ODVKLQJ²*URXQGGHWHFWVZLWFKLVDFWLYDWHG
)ODVKLQJ²2XWHUEDUULHUXSVZLWFKLVDFWLYDWHG
)ODVKLQJ²,QQHUUROOVWRSXSVZLWFKLVDFWLYDWHG
)ODVKLQJ²,QQHUUROOVWRSRFFXSLHGVZLWFKLVDFWL-
vated
)ODVKLQJ²2XWERDUGEDUULHURFFXSLHGVZLWFKLV
activated
)ODVKLQJ²7KUHVKROGWDSHVZLWFK´$µLVDFWLYDWHG
)ODVKLQJ²7KUHVKROGWDSHVZLWFK´%µLVDFWLYDWHG
)ODVKLQJ²3RVLWLRQVHWEXWWRQLVSUHVVHG
LCD Lift Codes
Listed below are codes that the lift controller outputs
during lift operation. The codes will be displayed
RQDQ/&'VFUHHQORFDWHGRQWKHOLIWFRQWUROERDUG
inside the pump module. See the Manual Operating
Instructions in the operator's manual for pump cover
removal instructions.
1RQ)ODVKLQJ1XPEHUV
01 – Platform stowed
02 – Platform unfolding
03 – Platform unfolding paused
²3ODWIRUPDWÁRRUOHYHO
05 – Platform beginning to lower
06 – Platform lowering (threshold cannot be occu-
pied from this point down)
07 – Outer barrier moving to horizontal position
08 – Platform at ground level
09 – Outer barrier moving to vertical position
10 – Platform raising
²3ODWIRUPUDLVLQJSDXVHGDWÁRRU
12 – Platform folding (limited pressure)
13 – Platform folding (full pressure)
14 – Timed fold (cinching lift tite) or (anti-rattle state)
15 – Platform folding stopped
16 – Paused fold
17 – Platform between ground and 3” above ground
18 – Platform above 3”
19 – Outer barrier moving to horizontal postion
23 Outer barrier going back down after occupant
detected
²,OOHJDOIXQFWLRQQRWGHÀQHG
29 – Interlock fault not recognized (or has been
cleared but a motion button is still pressed)
30 – Platform location unknown
31 – Platform location transition state; attempting to
locate position
35 – Two or more motion buttons are being pressed
36 – The retention belt cannot be buckled while try-
ing to fold or unfold
37 – Motion button being pressed is not a valid mo-
tion
50 – Outer barrier is not up above inboard barrier
locked position
51 – Threshold is occupied when platform is 1” or
PRUHEHORZÁRRUOHYHO
52 – Inner rollstop is not up and locked below inner
rollstop locked position
53 – Inner rollstop occupied sensor is not activated
EHWZHHQÁRRUDQGLQQHUUROOVWRSXSSRVLWLRQ
54 – Outer barrier is occupied before it is up
55 – Outer barrier is not latched when above the in-
ner rollstop locked position (Millennium only)
56 – Outer barrier is not up and latched and bridge
switch did not deactivate
 previous next