To enjoy High Bit rate Audio and Video
Enjoying High Bit rate Audio with 7.1ch speaker
This unit can decode high bit rate audio (Dolby Digital Plus, Dolby TrueHD, DTS-HD High Resolution Audio and DTS-HD Master Audio) adopted
in BD-Video.
To enjoy 7.1ch surround sound, the following conditions are necessary (Part shown in the shaded area of table given below).
Connect an amplifi er/receiver with 7.1ch speaker supporting HDMI (High Bit rate Audio) using a High Speed HDMI cable. (➡ 100)
Set “BD-Video Secondary Audio” to “Off” in the Setup menu. (➡ 91)
Set “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” to “Bitstream” or “PCM” in the Setup menu. (➡ 91)
About audio from audio output terminal
Connect an amplifi er/receiver and confi rm the desired audio type and necessary settings (“BD-Video Secondary Audio”, “Dolby D/Dolby D +/
Dolby TrueHD” or “DTS/DTS-HD”).
The number of channels listed is the maximum possible number of output channels.
Also, depending on the specifi cations or the settings of the amplifi er/receiver, the results of the output may vary.
Terminal HDMI AV OUT DIGITAL AUDIO OUT
“Dolby D/Dolby D +/
Dolby TrueHD”/
“DTS/DTS-HD”
“Bitstream”
1
“PCM”
3
“Bitstream” “PCM”
“BD-Video
Secondary Audio”
“On”
2
“Off” “On” “Off” “On”/“Off” “On”/“Off”
Dolby Digital/
Dolby Digital EX
5
Dolby Digital/
Dolby Digital
EX
6
Dolby Digital/
Dolby Digital EX
5.1ch PCM
Dolby Digital/
Dolby Digital
EX
6
Down-mixed 2ch
PCM
Dolby Digital Plus
Dolby Digital
Dolby Digital Plus
5.1ch PCM
2
7.1ch PCM Dolby Digital
Dolby TrueHD Dolby TrueHD
DTS Digital
Surround/
DTS-ES
5
DTS Digital
Surround/DTS-
ES
6
DTS Digital
Surround/
DTS-ES
DVD-V
5.1ch PCM DTS Digital
Surround/
DTS-ES
6
BD-V
7.1ch PCM
4
DTS-HD High
Resolution Audio
DTS Digital
Surround
DTS-HD High
Resolution Audio
7.1ch PCM
4
DTS Digital
Surround
DTS-HD Master
Audio
DTS-HD Master
Audio
7.1ch LPCM
Down-mixed
5.1ch PCM
7.1ch PCM
Down-mixed
5.1ch PCM
2
7.1ch PCM
Down-mixed 2ch
PCM
1
When the connected equipment is not supported with these audio format, the audio is output as Dolby Digital bitstream, DTS Digital Surround
bitstream or down-mixed 2ch PCM (e.g., TV).
2
BD-V
: When playing BD-Video without secondary audio or clicking sound, the audio is output as the same format as if “BD-Video Secondary
Audio” was set to “Off” in the Setup menu. (➡ 91)
3
When the connected equipment is not supported with multi channel surround, the audio is output as down-mixed 2ch PCM.
4
BD-V
: When the connected equipment is supported with 7.1 channel surround, the audio output is amplifi ed from 5.1ch or 6.1ch to 7.1ch
depending on the DTS, Inc. specifi cations.
5
With PCM output, Dolby Digital EX becomes PCM audio decoded as Dolby Digital, DTS-ES recorded to DVD-Video becomes PCM audio
decoded as DTS Digital Surround, and DTS-ES recorded to BD-Video becomes PCM audio decoded as DTS-ES.
6
BD-V
: When “BD-Video Secondary Audio” is set to “On” in the Setup menu, Dolby Digital EX is output as Dolby Digital and DTS-ES is output
as DTS Digital Surround, however if playing BD-Video without secondary audio or clicking sound, the audio is output as the original format.
Note
When setting “BD-Video Secondary Audio” to “Off” in the Setup menu, the clicking sound on the menu and audio with secondary video in
picture-in-picture mode (➡ 44) cannot be output.
Regarding 24p output
Many BD-Video movie contents are recorded in 24 frames/second in accordance with the fi lm materials. However, they will normally be output in
60 frames/second in accordance with the display format.
These can be output in 24p as the original. Therefore, high-quality video can be enjoyed, such as the improved clarity, enhanced perspective,
etc.
Preparation
Connect to a TV supporting 1080/24p input via an HDMI cable.
Set “BD-Video 24p Output” to “On” in the Setup menu. (➡ 92)
DMR-BW850GL_en.indb 45DMR-BW850GL_en.indb 45 2009/04/08 午前 10:01:002009/04/08 午前 10:01:00
