17
FUNCTION CODE LOCAL PROGRAMMING TELEPHONE PROGRAMMING
05
MANUAL ACCESS
RELAY CONTROL
This command can be used to
latch the access relay indefi nitely
or for a period of time, and to
unlatch the access relay.
Step 1 Enter Function Code 05, then press #.
Step 2 Enter the number of hours from 01-98 to
energize the access relay, then press #.
- OR -
Enter the 99 to energize the access
relay indefi nitely, then press #.
- OR -
Enter the 00 to de-energize the
access relay, then press #.
- OR -
Enter ✱ to cancel this command.
Step 1 Enter Function Code 05 and
press #, one short beep sounds.
Step 2 Enter the number of hours from 01-98 to
energize the access relay, then press #.
- OR -
Enter the 99 to energize the access
relay indefi nitely, then press #.
- OR -
Enter the 00 to de-energize the
access relay, then press #.
Two long beeps and two
short beeps will sound.
06
DIRECTORY CODE
LENGTH
Selects 2 or 3 digits for the
Directory Code length (factory
default is 3 digits).
NOTE: In multi-unit installations, if
sub-units are being updated with
access data that has Directory
Codes with more digits than the
sub-unit is set for, the sub-unit’s
Directory Code length number will
be automatically adjusted to fi t.
Step 1 Enter Function Code 06, then press #.
Step 2 The display shows the current value.
Enter 2 or 3, then press #.
- OR -
Enter ✱ to cancel this command.
NOT AVAILABLE
10
WELCOME DISPLAY
TEXT
The AE-100 display will show
a visitor a welcome message
alternating with instructions on
how to fi nd and call a resident.
The welcome message can be
customized to suit the installation.
Step 1 Enter Function Code 10, then press #.
Step 2 Enter the new welcome message. A total of 32
characters are allowed. The display will advance
to the lower line after the 16th character is
entered on the upper line. Enter # after each
character, enter ## after the last character.
NOT AVAILABLE
30
COPY ACCESS
DATA ONLY FROM
MASTER TO
SUB-UNITS
To synchronize programming
in multi-unit installations, the
Directory Entries and Stand-alone
Entry Codes can copied from the
master unit to selected sub-units.
CAUTION: This utility
command will overwrite ALL the
access data in the sub-unit(s)
selected.
Step 1 Enter Function Code 30, then press #.
Step 2 Enter the number(s) (2, 3, and/or 4) of all the
sub-units to copy the data to, then press #.
Step 3 Enter 5 for verifi cation, then press #.
- OR -
Enter ✱ to cancel this command.
NOTE: The installer must setup the system as a multi-unit
installation before this command will operate.
Step 1 Enter Function Code 30 and
press #, one short beep sounds.
Step 2 Enter the number(s) (2, 3, and/or 4)
of all the sub-units to copy the data to,
then press #, one short beep sounds.
Step 3 Enter 5 for verifi cation, then press #,
two short beeps sound. (Any entry other
than 5# will cancel the command.)
NOTE: To allow for multi-unit network
communications, when executing this
command remotely over the telephone,
the system will disconnect your call
after Step #3 then copy the data from
the master unit to the sub-units.
O P E N : 0 0 H O U R S
D I R D I G I T S : 3
( B L A N K D I S P L A Y )
U N I T S :
A R E Y O U S U R E ? 5
ALTERNATE PROGRAMMING METHOD
