A SERVICE OF

logo

Open as PDF
next previous
"'-"
BdYZa<%,((B[\#H^cXZ&%$&&
2. BV`ZVXZciZgbVg`Wnjh^c\VlddYbVaaZi
VcYiVee^c\i]Zed^cid[i]ZhejgXZciZg^cid
i]ZXZciZgd[i]Zldg`e^ZXZdcWdi]ZcYh#
3. Jh^c\V
&
¿)Yg^aaW^i!Yg^aaV
&
¿)YZZe]daZVii]Z
XZciZgbVg`dci]ZZcYd[i]Zldg`e^ZXZid
WZbdjciZYdci]Z]ZVYhidX`hejgXZciZg#
4. Id ]Zae ZbWZY i]Z hejg XZciZg ^cid i]Z
ldg`e^ZXZ! Xji
&
¿- YZZe hVl `Zg[h ^c i]Z
]ZVYhidX` ZcY d[ i]Z ldg`e^ZXZ Vadc\ i]Z
Y^V\dcVaa^cZhbVg`ZY^cStep 1#
5. >[ndjgldg`e^ZXZ^hdkZg'm'!Xjii]ZXdg"
cZgh d[[ i]Z ldg`e^ZXZ aZc\i]l^hZ id bV`Z
ijgc^c\hV[ZgVcYZVh^ZghZZFigure 37#
6. 9g^kZ i]Z hejg XZciZg ^cid i]Z ZcY XZciZg
bVg`d[i]Zldg`e^ZXZl^i]VlddYbVaaZiid
ZbWZY^i ViaZVhi
&
¿)^cid i]Zldg`e^ZXZ! Vh
h]dlc^cFigure 38#
&$)
Figure 38.HejgXZciZgegdeZganZbWZYYZY#
Ldg`e^ZXZ
8ZciZg
Figure 37.8dgcZghd[ldg`e^ZXZgZbdkZY#
7. L^i] i]Zldg`e^ZXZ hi^aaViiVX]ZY! ^chZgi i]Z
hejgXZciZg^cidi]Z]ZVYhidX`he^cYaZgZ[Zg
id Installing/Removing Headstock Center
dcPage 23 [dgVYY^i^dcVa^chigjXi^dch#
Note: Use the tool rest to support the opposite
end of the workpiece so that the workpiece
and spur center do not separate during
installation.
8. >chiVaa i]Z a^kZ XZciZg ^cid i]Z iV^ahidX` fj^aa
VcYi^\]iZci]Z fj^aaadX`]VcYaZ idadX`i]Z
fj^aa ^c edh^i^dc gZ[Zg id Page 24 [dg VYY^"
i^dcVa^chigjXi^dch#
9. Ha^YZ i]Z iV^ahidX` idlVgY i]Z ldg`e^ZXZ
jci^ai]Zed^cid[i]Za^kZXZciZgidjX]Zhi]Z
ldg`e^ZXZXZciZgbVg`!i]ZcadX`i]ZiV^ahidX`
^ci]^hedh^i^dc#
10. AddhZc i]Zfj^aa adX` ]VcYaZVcY gdiViZi]Z
iV^ahidX` ]VcYl]ZZa id ejh] i]Z a^kZ XZciZg
^cidi]Zldg`e^ZXZViaZVhiV
&
¿)#
11. EgdeZganVY_jhii]ZiddagZhiidi]Zldg`e^ZXZ
hZZ Adjusting Tool Rest dc Page 23#
12. 7Z[dgZWZ\^cc^c\ aVi]ZdeZgVi^dc!gdiViZi]Z
ldg`e^ZXZ Wn ]VcY id ZchjgZ i]Vi i]ZgZ ^h
hV[ZXaZVgVcXZdcVaah^YZh#
Keep the lathe tool resting on the tool
rest the ENTIRE time that it is in contact
with workpiece or when preparing to make
contact between lathe tool and workpiece.
Otherwise, the spinning workpiece could
force the lathe tool out of your hands or
entangle your hands with the workpiece.
Failure to heed this warning could result in
serious personal injury.
Do not press the workpiece too firmly with
the tailstock or the bearings will bind and
overheat. Do not adjust the tailstock too
loosely or the workpiece will spin off the
lathe. Use good judgment and care, other-
wise, serious personal injury could result
from the workpiece being ejected at high
speeds.