A SERVICE OF

logo

Open as PDF
next previous
BdYZa<%,((B[\#H^cXZ&%$&&
"'*"
=ZVYhidX`;VXZeaViZ
Installing Faceplate
To prevent the faceplate and workpiece sep-
arating from the spindle during operation,
the headstock faceplate MUST be firmly
threaded onto the spindle and secured in
place by fully tightening the two faceplate
set screws. If these instructions are not
properly performed, serious personal injury
could occur.
Note: To remove the faceplate, disconnect the
lathe from the power source and perform the
steps above in reverse.
To install the faceplate:
1. 9>H8DCC:8IA6I=:;GDBEDL:G
2. >chZgii]Z^cYZm^c\e^c^ciddcZd[i]Z^cYZm"
^c\]daZhVcYgdiViZi]Zhe^cYaZjci^ai]Ze^c
Zc\V\ZhidegZkZcii]Zhe^cYaZ[gdbijgc^c\
l]^aZndji^\]iZci]Z[VXZeaViZ!Vhh]dlc^c
Figure 26#
3. I]gZVYi]Z[VXZeaViZdcidi]Zhe^cYaZjci^a^i
^hhcj\#
4. Jh^c\i]Z^cXajYZY)bb]ZmlgZcX]!i^\]iZc
i]ZildhZihXgZlhVadc\i]Z^ch^YZY^VbZiZg
d[ i]Z [VXZeaViZ id hZXjgZ ^i id i]Z he^cYaZ
hZZFigure 26#
Figure 26.AdX`^c\he^cYaZl^i]^cYZm^c\e^cVcY
[VXZeaViZhZihXgZladXVi^dc#
;VXZeaViZHZi
HXgZl&d['
Changing Speed
Ranges
I]Z BdYZa <%,(( ]Vh ejaaZn WZai Xdc[^\jgVi^dc
egdk^YZYildheZZYgVc\ZhhZZFigure 27#
Note: To maximize spindle torque, use the low
spindle speed range for spindle speeds of 1200
RPM or less.
GZ[Zg id i]Z heZZY gZXdbbZcYVi^dch X]Vgi ^c
Figure 28idX]ddhZi]ZVeegdeg^ViZGEB[dgndjg
deZgVi^dc#I]ZcX]ddhZi]ZheZZYgVc\Zi]Vil^aa
^cXajYZi]ZhZaZXiZYGEB#
8]Vc\^c\HeZZYGVc\Zh
Diameter
of Work-
piece
Roughing
RPM
General
Cutting
RPM
Finishing
RPM
JcYZg' &*'% ('%% ('%%
'¶) ,+% &+%% ')-%
)¶+ *&% &%-% &+*%
+¶- (-% -&% &')%
-¶&% (%% +*% &%%%
&%¶&' '** *)% -(%
&'¶&) ''% )+% ,&%
&)¶&+ &.% )%% +'%
Figure 28.BdYZa<%,((heZZY
gZXdbbZcYVi^dch#
To change speed ranges:
1. 9>H8DCC:8IA6I=:;GDBEDL:G
Figure 27.HeZZYgVc\ZWZaiedh^i^dch#
He^cYaZ
Bdidg
7
6
6 2=^\]GVc\Z
((%"('%%GEB
7
2AdlGVc\Z
&%%"&'%%GEB