Remington MS3-2700 Electric Shaver User Manual


 
Cleaning your shaver:
TO ASSURE OPTIMAL PERFORMANCE,WE RECOMM E N D
T H AT YOU CLEAN YOUR SHAVER AFTER EACH USE.The
cutting system of this shaver was designed to be
cleaned by rinsing under warm running water or by
b r u s h i n g .( Water temperature should be between
40°C/104°F and 70°C/158°F.)
Cleaning your shaver is easy. (NOTE:With MS3-4700 model,
the brush icon will blink to remind you to clean your shaver.)
Remove the shaver head by
squeezing on both side buttons and
pulling away from the body of the
shaver.You may blow out the stub-
ble thoroughly, or rinse the shaver
head in water.
Important: Never clean the screen
with the enclosed brush as damage
may occur to the holes in the screen.
At least once a week,the cutters and
the trimmer should be cleaned with
the cleaning brush. You can also
rinse the cutter under running water,
like the screen.
Caution: Never put the shaver
completely under water.Do not use any
aggressive cleansing agent as this may
destroy the shaver coatings.
To clean and lubricate your shaver’s cutters and head
assembly, apply R e m i n g t o n
®
S h a ver Sav e r
®
( S P - 4 )
L u b r i c a n t . The lubricant helps remove hair clippings
while reducing wear.A quick spray after each shave
keeps your shaver operating at peak performance.
Caution: Do not remove or replace the head assembly while shaver
is running as it may cause damage to the unit’s screens or cutters.
Worn or damaged parts should be replaced with Remington
®
replacement parts only.
Replacing Screens and Cutters
Because they are subject to daily use,the cutters and screens of
your Remington
®
shaver will wear and e v e n t ually require replace-
ment to maintain a close,comfortable s h av e . Depending on your
s h aving technique and hab i t s , the screens will usually last six
months; the cutters,one year.
When is it time to replace your screens and cutters?
It is very important to replace your screens and cutters when nec-
essary to insure a close,comfortable shave without irritation.We
recommend they be replaced every 12 months.
Irritation: As foils get worn,you may notice that your skin feels
more sensitive after a shave,particularly when you apply after
shave.
Pulling: As cutters wear, your shave may not feel as close and
you may feel your shaver is pulling at your whiskers.
We a r- t h rough: You may notice that the cutters have worn through
the fo i l .
The replacement for this shaver is model SP-94 for screens and
cutters and SP-93 for screens only. U . S .r e s i d e n t s :To order, c o n-
tact us at 800-736-4648, visit us at www. r e m i n g t o n - p r o d u c t s . c o m
or visit your local retailer. Canadian residents:For any shaver acces-
s o ry requirements, please call 800-268-6531 or write:R e m i n g t o n
Products (Canada) Inc., P. O . Box 601. Postal Station ‘ ’ T ’’ ,D e p t .A -
1 0 0 , 3019 Dufferin St.,To r o n t o ,Canada M6B3T7
To prevent inadvertent damage to the screen and cutter
assembly, do not attempt to remove them unless you are
replacing them. To remove the old screens and cutters follow the
instructions that come with the screen and cutter,replacement pack-
age.It’s always a good idea to replace the screens when you replace
the cutters.
To Replace a Cutter Assembly That is Removed
Unintentionally:
Hold the assembly in the middle of
the "T".
Gently slide the plastic portion of the
cutter assembly over the top of the
oscillator tip.
Do not push downward on the ends of
the cutters,as you may bend the cutter,
reducing its ability to operate smoothly.
Do not remove cutters from the plastic
pieces to which they are attached,as
you may damage the assembly.