Filter
Top Products
motions trim area directly
under the beard line.
To Thin and Taper Beard
1. Use a small comb to hold
hairs in place while trim-
ming.
2. Hold Trimmer with front of
Trimmer facing away from
you.
3. Trim hair ends using an
upward motion.
4. Turn Trimmer OFF.
To Trim Moustache with
Trimmer Guard Attachment
• Be certain Trimmer Guard
Attachment is on to prevent
trimming off too many
hairs.
1. Comb hairs outward so
they are at their maximum
height and in the same
direction.
2. Set Zoom Ring to desired
setting.
• Hold Trimmer vertically
with front of Trimmer fac-
ing you.
• Trim hairs using a down-
ward motion following the
direction of your hair growth
or you may trim against
your hair growth—
whichever is preferred.
NOTE: Since all hairs do not
grow in the same direction,
you may want to try differ-
ent trimming positions (i.e.
upwards, downwards or
across). Practice is best for
optimum results.
To Trim Moustache without
Trimmer Guard Attachment
1. Remove Trimmer Guard
Attachment.
2. Place a finger on upper lip
to lift hair up, away from
skin.
3. Trim hairs using an upward
motion.
4. After achieving desired
length, use a downward
motion to blend moustache
hairs (Fig. 8).
To Trim Moustache with Pop-
Up Trimmer: Model
T-7000 only
1. Slide Pop-Up Trimmer
switch up (Fig. 9).
2. Hold Trimmer perpendicu-
lar as shown and move cut-
ters sideways to achieve
desired line above lip (Fig.
10).
3. Trim any stray hairs.
4. Slide Pop-Up Trimmer
down when finished.
ATTENTION: Main cutter is
still operating while Pop-Up
Trimmer is in use.
NOTE: Use a slow and gen-
tle pressure. Too much
pressure may trim more
hair than desired.
5. Turn Trimmer OFF.
To Trim Sideburns
1. Comb sideburns following
the direction of your hair
growth.
2. Be certain Trimmer Guard
Attachment is ON.
3. Hold Trimmer vertically
with front of Trimmer fac-
ing you.
4. Trim sideburns using a
downward motion.
5. Turn Trimmer OFF.
To Achieve The
“Stubble” Look
• The Trimmer Guard
Attachment is unique
because it has a small slot
between the two rows of
teeth enabling you to trim
hairs to only .06 in./1.5mm
in length.
1. Be certain Trimmer Guard
Attachment is ON and
Zoom Ring is on the lowest
setting (#1).
2. Hold Trimmer horizontally
with front of Trimmer facing
downwards or upwards.
3. Trim hairs using a down-
ward or upward motion,
whichever is more comfort-
able, following the direction
of your hair growth.
4. Turn Trimmer OFF.
IMPORTANT
• Always switch Trimmer
OFF before cleaning.
• Never clean, remove or
replace Trimmer Guard
Attachment with motor on.
• Do NOT apply pressure to
cutters.
• Do NOT touch cutters
with hard objects as this
may damage them.
• DO NOT use while
bathing, showering or
immerse the unit in water
or other liquids as damage
to Trimmer may occur.
• NEVER use harsh or cor-
rosive cleaners such as
benzene or bleach.
During Use
• If cut hairs have accumu-
lated in the comb area,
pull Trimmer Guard
Attachment off Trimmer
(Fig. 11) and remove hairs
by shaking and/or blowing
(Fig. 12).
Once A Week
1. Be certain Trimmer is in
OFF position.
2. Remove Trimmer Guard
Attachment (Fig. 11).
3. Hold Trimmer as shown
and gently pull cutter
backwards (Fig. 13).
4. Lightly brush out cutters,
hair chamber and
Trimmer Guard Attach-
ment (Fig. 14 &15) with
cleaning brush provided.
To Replace Cutters
If your cutters become dam-
aged or worn, do not contin-
ue using the Trimmer.
Replace cutters immediately.
1. Remove the old cutters by
pulling cutting unit back-
wards (Fig. 13) and then
pull it upwards off
Trimmer.
2. Install new Trimmer by
placing the two notches of
the new cutting unit into
the guide slots (Fig. 16).
3. Push the cutting unit
backuntil it “clicks” into
place (Fig. 17).
10
8
9
Trimmer Guard Attachment (continued) Maintenance
11
12
13
14
2
1
15
16
2
1
1
17
CLICK
Downloaded from www.Manualslib.com manuals search engine