Filter
Top Products
INS245
Faucets made of leaded brass alloys may contribute small amounts of lead to water that is
allowed to stand in contact with the brass. The amount of lead contributed by any faucet is
highest when the faucet is new.The following steps may reduce potential exposure to lead
from faucets and other parts of the plumbing system:
• Always run the water for a few seconds prior to use for drinking or cooking
• Use only cold water for drinking or cooking
• If you wish to flush the entire plumbing system of water that has been standing in the
pipes or other fittings, run the cold water until the temperature of the water drops,
indicating water coming from the outside main
• If you are concerned about lead in your water, have your water tested by a certified
laboratory in your area
Moen products have been manufactured under the highest standards of quality and workmanship. Moen
warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the
“Warranty Period” for homeowners), that this faucet will be leak and drip-free during normal use and all parts and
finishes of this faucet will be free from defects in material and manufacturing workmanship. All other purchasers
(including purchasers for industrial, commercial and business use) are warranted for a period of 5 years from the
original date of purchase (the “Warranty Period” for non-homeowners).
If this faucet should ever develop a leak or drip during the Warranty Period, Moen will FREE OF CHARGE
provide the parts necessary to put the faucet back in good working condition and will replace FREE OF CHARGE,
any part or finish that proves defective in material and manufacturing workmanship, under normal
installation, use and service. Replacement parts may be obtained by calling
1-800-289-6636 (Canada 1-800-465-6130), or by writing to the address shown. Proof of purchase (original sales
receipt) from the original consumer purchaser must accompany all warranty claims. Defects or damage caused
by the use of other than genuine Moen parts are not covered by this warranty. This warranty is applicable only to
faucets purchased after December 1995 and shall be effective from the date of purchase as shown on purchaser’s
receipt.
This warranty is extensive in that it covers replacement of all defective parts and finishes. However, damage
due to installation error, product abuse, product misuse, or use of cleaners containing abrasives, alcohol or other
organic solvents, whether performed by a contractor, service company, or yourself, are excluded from this
warranty. Moen will not be responsible for labor charges and/or damage incurred in installation, repair or
replacement, nor for any indirect, incidental or consequential damages, losses, injury or costs of any nature
relating to this faucet. Except as provided by law, this warranty is in lieu of and excludes all other warranties,
conditions and guarantees, whether expressed or implied, statutory or otherwise, including without restriction
those of merchantability or of fitness for use.
Some states, provinces and nations do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights
and you may also have other rights which vary from state to state, province to province, nation to nation. Moen
will advise you of the procedure to follow in making warranty claims. Simply write to Moen Incorporated using
the address below. Explain the defect and include proof of purchase and your name, address, area code and
telephone number.
WARRANTY CONSUMER INFORMATION
INSTALLATION INSTRUCTIONS
3
Moen Incorporated • 25300 Al Moen Drive • North Olmsted, OH 44070-8022 U.S.A. In Canada Moen Inc.• 2816 Bristol Circle • Oakville,Ontario L6H5s7
HELPLINE:
1 (800) BUY-MOEN
[289-6636]
In the U.S. call our toll free Helpline number, for answers to
any product installation, or warranty questions.
In Canada:
Toronto:905-829-3400;
Rest of Canada: 1-800-465-6130
In Mexico:
(84) 88-08-26, 88-08-27,
o 91-800-84-345
IMPORTANT: Pipe chips, sand, stones and other solids found in new and
renovated plumbing can damage the sealing surfaces of the cartridge and
cause a leak. To avoid damage, DO NOT TURN ON SUPPLY VALVES
until instructed below.
1. After installing and connecting your new bidet faucet, turn the diverter
handle clockwise to the rim flush mode and open both hot and cold
cartridges.
2. Turn on both hot and cold water supply valves and allow the water to run
for 15 seconds.
3. Turn off the hot and cold cartridges and check the system for leaks.
FLUSHING INSTRUCTIONS
INSTALLATION OF SUPPLY HANDLES & ESCUTCHEONS
1. Apply 1/4" bead of plumbers putty (not supplied) under the bottom of the handle escutcheon. Center escutcheon over valve bodies.
2. Rotate stem extensions to off position; clockwise for hot counterclockwise for cold.
3. Position lever handles on valves pointing away from diverter handle.
4. Holding lever or cross handle, hand tighten handle hub clockwise.
5. Faucet flushing is required. See instructions below.
Plumbers Putty
Stem Extension
Handle Hub