Filter
Top Products
19510317700 English, All Logos to be Ariston {PDF Created 18/01/13 22:04:00}
11
Start and Programmes
TD4239FUV Issue 4
The Controls
• Programmes knob
! Warning,
if after pressing the start button the programme
knob position is changed, the new position will NOT change
the programme selected. To change programme press
Start/Pause Button
to pause the programme, the light flashes
A
mber to indicate the programme is paused. Select the new
programme and any options required, the light will then flash green.
Press the Start/Pause Button
and the new programme will start.
• Option Buttons/ Lights
These buttons are used to customise the selected programme
to your requirements. A programme must have been selected
on the Programmes knob before an option can be selected.
Not all options are available for all programmes (see Start and
Programmes). If an option is not available and you press the
button, the buzzer will beep three times. If the option is
available the option light in the button lights to confirm your
selection.
A
fter the start switch has been pressed were available only the
Crease Care or Sound options (were available) can be
changed.
• Progress ( Drying, Cool tumble), Icons
These are part of the Display unit they indicate the progress of
the dryer each one comes on as the corresponding phase
starts.
• Time Delay
The start of some programmes (see Start and Programmes and
The Display) can be delayed for up to 24 hours.
Crease care
The pre-care option is only available if a delayed start has
been selected. It tumbles the clothes occasionally during the
delayed period to help prevent creases developing.
The post-care option occasionally tumbles the clothes after the
end of the drying and cool tumble cycles to help prevent
creases developing, should you not be available to remove the
load immediately the programme is complete. The Display
shows
, the Crease care and the Start/Pause Lights flash
A
mber. during this phase. Selecting this option enables both
the pre and post care functions if appropriate and when
selected the light in the button is on.
Note: If you have selected the Sound option this option is not
available.
Sound
If selected gives a signal at the end of the drying cycle to
remind you that the clothes are ready to be removed. Not
available on Heat & Enjoy programme.
Note: If you have selected the Crease care option this option is
not available.
• Heat Level Button and Lights
Not all programmes allow you to change the heat level, and
some of these programmes do allow all three heat level
options. When the option change the heat level is available
pressing this button changes the heat level selected and the
corresponding light is lit for the three available levels, Low,
Medium and Hi
g
h.
DISPLAY
The display shows either the amount of time delay remaining
or an indication of the amount of time left for a drying
programme. (see The Display) The Colons between the hours
and minutes display flash to show that the time is counting
down.
When the programme finishes its cool tumble phase the
display will show
.
• Door Opening
Opening the door (or pressing the Start/Pause Button )
during a programme will stop the dryer and have the following
effects.. Note: The Start/Pause Light flashes Amber during
Post Care phase of a programme.
• The Start/Pause Light flashes Amber.
• The start button
must be pressed to resume
the programme including a delayed start. The
progress lights will then change to show the
current status and the Start/Pause light will stop
flashing and turn green
• During a delay phase the delay will continue to
count down...
• During the drying part of a programme, the time to
end count continues but the colons do not flash.
• During the post care part of a drying program, the
programme will finish. Pressing the start/pause
button will re-start a new programme.
• Changing the Programmes knob will select a new
programme and the Start/Pause Light will flash
green. You can use this to select the Refresh
programme
to cool the clothes if you find them
dry enough.
Press the start button
to begin new
Programme
• Note
If you have a power cut, switch off the power or remove
the plug. When power is restored, press and hold the
On/Off button until the dryer reactivates, then press the
Start/Pause button.