SAFETY GUIDE - PLEASE READ CAREFULLY
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
Please follow all the safety precautions listed below for safety
instruction concerning use of the appliance by a person
and to reduce the risk of injury or electrical shock.
responsible for their safety.
$Read all the instructions carefully before using your
$Children should be supervised to ensure that they do not
blender and keep them for future reference.
play with the appliance.
$Unplug the appliance from the mains supply when not
in use, when removing or attaching accessories, or
When operating this appliance:
before cleaning any part of the appliance.
$When the appliance is not in use make sure that it is
$This appliance is for occasional household use only.
safely unplugged from the mains supply.
$Do not use outdoors or in damp conditions.
$To reduce the risk of injury, ensure that the cutting blade
$Do not immerse the motor unit or the electrical cord or
is fully retracted when not in use.
plug in liquids.
$When using the appliance ensure there is adequate
$Do not use near a source of heat or on an unstable
room to work.
surface.
$Do not run the appliance continuously for more than 6
$Ensure that the power cord does not touch any hot
minutes After 6 minutes of continuous use let the unit
surface and that it does not overhang the edge of your
cool for 15 minutes before using it again.
work surface.
$The slicing knife on this appliance is sharp. Treat it with
$When unplugging the power cord, hold the plug top, not
care at all times and never allow fingers, hair, or
the power cord.
clothing to come into contact with the blade.
$Do not operate any appliance with a damaged cord or
$
plug or after the appliance malfunctions, or is dropped
or damaged in any manner. Return the appliance to the
$Do not slice hard or dense materials (such as hard
nearest authorised service facility for examination,
cheeses) which cannot safely be sliced by the knife.
repair or electrical or mechanical adjustment.
$DO NOT slice food containing bones or frozen food.
$Do not use attachments or accessories which are not
$Very soft materials (i.e. Mozzarella Cheese)may tear, If
recommended by the manufacturer. They may cause
there is any sign of tearing discontinue slicing the
malfunction or injury.
material.
$Do not attempt to replace the power cord on this
$If the knife gets clogged, switch off, and allow the unit to
appliance. This should only be carried out by authorised
stop before clearing the obstruction.
service personnel with specialist tools.
$If the motor slows down or the blade gets hot, switch off,
$Store the appliance away from direct sunlight and out of
and allow the unit to stop and cool down before
the reach of children.
recommencing slicing.
$There are no user serviceable parts in your appliance
$Operate the appliance is on a sturdy work surface. and
Unauthorised dismantling or servicing will void the
hold or support it during operation
product warranty.
$Do not yank or pull the cord as this may damage it and
$Do not use the appliance for any purpose not expressly
eventually cause a risk of electric shock.
specified in this manual.
$To protect against fire, do not operate the unit in the
$This appliance is not intended for use by persons
presence of explosive and/or flammable fumes.
(including children) with reduced physical, sensory or
$Keep the unit out of the reach of children
Hold the knife blade by the clamp when removing and
attaching it to the appliance.
COMPONENTS AND CONTROLS
Page 2 Page 3 Page 4
UNPACKING
Before every use of your appliance:
$ Remove the Collecting Tray (2). (See Figure 1)
$Remove all packaging from the appliance. Retain the
$Wash the plastic components (12, 13, 14) and the tray (2)
packaging. If you dispose of it please do so according to
in warm soapy water , rinse and dry thoroughly.
any recycling regulations.
$Open the appliance and remove the slicing knife (7) (see
$Read and retain the manual. If you pass the product on
Fig.3) Wash in warm soapy water taking care not to touch
to a third party, make sure to include this manual.
the cutting surfaces, rinse and dry thoroughly.
PRELIMINARIES
$Wipe the motor unit (3), and the Tables(6, 10, 11) all
Always make sure the appliance is unplugged from the
over with a soft cloth dampened with soapy water
mains when cleaning, attaching or removing accessories
followed with a clean damp cloth. Dry well. Do not
Refer to the assembly instructions on the next page and the
immerse the motor unit, mains cable or plug in water.
illustrations above.
$Replace the Slicing Knife and assemble the unit for use.
PREPARATION FOR USE
2: Assemble the Sliding Table and Guard:
Hold the table down. Line the three tabs on the bottom of
the Guard with the slots in the top of the Sliding table and
push the Guard into place. make sure the Guard is firmly
locked to the table. Once assembled we do not recommend
dis-assembly of the table.
4: Attach the Sliding Table
1: Ensure the Slicing Knife edge is safely behind the Slice
adjustment table . (See Figure 6).
2: Line the tab under the Sliding
table with the slot in the Base Plate.
Insert the table into the slot and press
gently. Slide the table back and forth
and check it moves freely but securely
over the base plate. (See View B on Page 2).
FS10 USER GUIDEFS10 USER GUIDE
1: Thickness Adjustment Dial
2: Collecting Tray
3: Motor Housing
4: Safety Switch
5: Thickness Indicator
6: Slicing Table
7: Slicing Knife
8: Slicing Knife Clamp
9: On/Off Button
10: Rear Plate
11: Base Plate
12: Sliding Table
13: Slice Feed Plate
14: Sliding Table Guard
3
2
VIEW A
3: Removing and Replacing the Slicing Knife
Ensure the sliding table is removed.
A: Rotate the Clamp Clockwise
to unlock the Slicing Knife and
Anticlockwise to lock it.
B: Hold the knife blade by the
clamp when removing and
attaching it.
To attach the Slicing Knife, hold it as shown, place it into the
recess in the motor and rotate anticlockwise.
NEVER TOUCH THE BLADE EDGE WITH YOUR FINGERS!
UNLOCK
LOCK
Fig 3A
Fig 3B
Figure 2
FS10 USER GUIDE
1: Ensure the machine is disconnected from the mains.
Invert the unit. Place the unit on a solid level surface and
hold it securely. Detach the Collecting Tray.
Figure 1
Fig 4A
5: Attach the Slice Feed Plate
Place the Slice Feed Plate over the Sliding Table Guard as
shown.
Slide it back and forth and ensure it moves freely.
Fig 5BFig 5A
1
10
5
6
7
8
11
12
13
9
VIEW B
14
4
