67
Menu Contents
Chapter 4 Menu Settings
SHUTTLE MUTE [> Shutl mute]: Set the audio muting
conditions during shuttle playback.
*OFF [>> OFF]: Not muted.
CUEUP or PREROLL [>> CUEUP]: Muted during cue-up or
preroll operations.
FULL [>> FULL]: Muted in shuttle mode.
AUDIO EDIT [> Audio edit]: Specify the type of editing for
audio signals.
*CUT EDIT [>> Cut edit]: Cut editing (Discontinuity in audio
signal may result at the editing point, causing noise during
playback.)
FADE IN/OUT [>> Fade]: Fade in and fade out
DV PB ATT [> DV PB ATT]: When playing back a tape
recorded in consumer DV format, select whether to
attenuate the audio output level.
OFF [>> OFF]: Do not attenuate.
*ON [>> ON]: Attenuate.
INTERFACE SELECT [Interface]: Settings related to
external interfaces
Description of settings
VIDEO OUTPUT [> Video Out]: Select the format of analog
video signals to be output from the three VIDEO OUT
connectors (Y/CPST, R−Y/C/CPST, and B−Y/CPST
(SUPER)).
Note
When this menu item is set to Y−R, B, the B−Y/CPST (SUPER)
connector outputs the B−Y signal. In this case, changing the
setting of an internal switch allows the text data for
superimposition on the monitor screen to be output from the
right-hand REF. VIDEO IN connector (marked ). For more
information about this, consult your Sony dealer.
*COMPOSITE [>> Composite]: Composite video signals
S-VIDEO [>> S-Video]: S-video (separated Y and C) and
composite video signals
Y−
−−
−R, B [>> Y−
−−
−R, B]: Y, R−Y and B−Y component video
signals
DIGITAL OUTPUT [> Digit Out]: Select the format of signals
to be output from the SDI/SDTI (QSDI) OUT1/OUT2
connectors (optional DSBK-1501 board required).
*SDI [>> SDI]: SDI format
SDTI [>> SDTI]: SDTI (QSDI) format
AUDIO OUTPUT [> Audio Out]: Select the channels for audio
output from the AUDIO OUT 1/3 and 2/4 connectors.
*1/2 CH [>> 1/2CH]: Output channel 1 to the AUDIO OUT 1/3
connector and channel 2 to the AUDIO OUT 2/4
connector.
3/4 CH [>> 3/4CH]: Output channel 3 to the AUDIO OUT 1/3
connector and channel 4 to the AUDIO OUT 2/4
connector.
REMOTE I/F [> Remote I/F]: When remote-controlling this unit
with the LOCAL/REMOTE switch set to REMOTE, select
either the REMOTE connector or i.DV IN/OUT connector
(optional DSBK-1501 board required) for connecting a
remote control unit.
*9PIN [>> 9PIN]: Remote-control via the REMOTE connector.
i.LINK [>> i.LINK]: Remote-control via the i.DV IN/OUT
connector.
SETUP BANK OPERATION [Setup Bank]: Settings related
to menu bank operations
Description of settings
RECALL BANK1 [> Recall 1]: Recall menu settings from
menu bank 1.
(1) Select the bank you want to recall, then press the
G
button.
Message “RECALL OK?” appears.
(2) To recall, press the SET (YES) button.
To quit recalling, press the RESET (NO) button.
RECALL BANK2 [> Recall 2]: Recall menu settings from
menu bank 2.
RECALL BANK3 [> Recall 3]: Recall menu settings from
menu bank 3.
RECALL BANK4 [> Recall 4]: Recall menu settings from
menu bank 4.
AUDIO CONTROL [Audio]: Settings related to audio
control
Description of settings
IN OUT
