ENGLISH
17
ADVANCED CONNECTING
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel
audio source such as a SACD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the
SETUP MAIN MENU. See page 32.
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifiers.
Be sure to connect each speaker to the corresponding
external power amplifier.
POWER
AMPLIFER
DVD AUDIO PLAYER
or
SACD MULTI CHANNEL
PLAYER
Center
Front
Left
Front
Right
Surround
Left
Surround
Right
Subwoofer
Surround
Back Left
CONNECTING TO THE RC-5 (MARANTZ PRODUCTS ONLY)
MD DECK
CD RECORDER
q
You can control other Marantz products through
this unit with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the
remote signal only to the unit. Also, if a Marantz
power amplifier (some models excluded) is
connected to one of these terminals, the power
amplifier’s, power switch is synchronized with this
unit’s power switch.
Set the REMOTE CONTROL SWITCH on the units,
other than the main unit to EXT.(EXTERNAL) for
this feature.
CD PLAYER
OPTION
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the ZR6001,
be sure to always disable operation of the infrared
sensor on the main unit by using the following
procedure.
1.
Hold down the MULTI button and MENU
button on the front panel at the same time for
five seconds.
2.
The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3.
Press the or cursor button to change this
to “IR=DISABLE”.
4.
Press the ENTER button. Once this setting is
made, the infrared sensor on the main unit is
disabled.
Note:
• Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not
connected. Otherwise, the main unit will be
unable to receive remote control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.
Surround
Back Right
MULTI
OUT
C
IN
OUT
S-VIDEO
DVD
DSS/VCR2
C
RC
MULTI
SBR
SBL
OUT
PRE
SL
L
SR
R
R
SW
RC-5
IN
SR
AUDIO
7.1CH
IN
IN
L
SL
SBR
SBL
IN
OUT
SW
OUT
CDR/MD
TAPE
IN
OUT
VCR1
TV
OUT
(
AUX2
)
MONITOR
COMPONENT VIDEO
C
B
/
P
B
C
R
/
P
R
C
R
/
P
R
C
R
/
P
R
C
B
/
P
B
C
B
/
P
B
INPUT-1
Y
MONITOR OUT
INPUT-2
Y
OUT
IN
FLASHER
MODE
C
C
SBR
SBL
OUT
PRE
SL
L
SR
R
R
SW
SR
7.1CH
IN
L
SL
SBR
SBL
SW
L
R
FRONT SURR.
SURR.
BACK
SUB
WOOFER
CENTER
L
R
FRONT SURR.
SURR.
BACK
SUB
WOOFER
CENTER
RL RL RL
LR
R L
LR LR
R L
RL RLRL
R L
MULTI
OUT
TV
DVD
C
IN
OUT
S-VIDEO
DVD
DSS/VCR2
C
RS-232C
RC
MULTI
IN
OUT
DSS/VCR2
IN
OUT
OUT
VCR1
VCR1
L
SBR
SBL
OUT
PRE
SL
L
SR
R
DSS/VCR2
DVD
TV
R
IN
R
SW
RC-5
IN
SR
AUDIO
7.1CH
IN
OUT
IN
L
SL
SBR
SBL
CD
IN
OUT
SW
OUT
CDR/MD
TAPE
OUT
IN
IN
OUT
VIDEO
MONITOR
VCR1
TV
OUT
(
AUX2
)
MONITOR
DIGITAL IN
DIGITAL OUT
3
1
OPT.
2
4
COAX.
FM
(
75
Ω
)
ANTENNA
GND
AM
COMPONENT VIDEO
C
B
/
P
B
C
R
/
P
R
C
R
/
P
R
C
R
/
P
R
C
B
/
P
B
C
B
/
P
B
INPUT-1
Y
Y
MONITOR OUT
INPUT-2
Y
OUT
IN
FLASHER
MODE
RC-5
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL
EXTERNAL INTERNAL
EXTERNAL INTERNAL
1
RC OUT
2
