8
ENGLISH
REAR PANEL (SR4002)
R
SR
C
SW
SBR
SL
SBL
L
R
SPEAKER SYSTEMS : 6-8 OHMS
SPEAKER SYSTEMS : 6-8 OHMS
CENTER
R
FRONT
SURROUND BACK
S. SPEAKER B
SURROUND
L
L
L
R
IN
2
1
4
3
OPT
DIGITAL OUT
(
AUX2
)
7.1CH INPUT
L
SL
C
SBL
R
SR
SW
SBR
R
L
FM
(
75
)
GND
AM
C
R
/
P
R
C
B
/
P
B
Y
ANTENNA
DIGITAL IN
OUT
IN
CD/CDR
OUT
IN
TAPE
VCR
DVD
TV
AUDIO
IN
OUT
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
C
R
/
P
R
C
B
/
P
B
Y
DSS
TV
DVD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT
INPUT
1
INPUT
2
S-VIDEO
VIDEO
IN
FLASHER
MODEL NO. SR4002
PRE OUT
AC IN
INPUT
3
INPUT 3
OUTPUT
INPUT 2
INPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
DSS
OUT
REMOTE CONT.
!0
u
i
y
!1 q r !6
!5
!3
!4
w
o
t
REAR PANEL (SR5002)
R
SR
C
SW
SBR
MULTI.
OUT
SL
SBL
L
R
R
XM
R
L
L
L
L
R
IN
OUT
REMOTE CONT.
OPT
DIGITAL OUT
(
AUX2
)
7.1CH INPUT
L
SL
C
SBL
R
SR
SW
SBR
RS-232C
SPEAKER C
OFF
ON
R
L
FM
(
75
)
GND
AM
C
R
/
P
R
C
B
/
P
B
Y
C
R
/
P
R
C
B
/
P
B
Y
1
ANTENNA
DIGITAL IN
OUT
IN
CD/CDR
OUT
IN
TAPE
VCR
DVD
TV
AUDIO
DSS
IN
OUT
C
R
/
P
R
C
B
/
P
B
Y
DSS
TV
DVD
VCR IN
VCR OUT
MONITOR OUT
MONITOR
OUT 2
INPUT
1
INPUT
2
S-VIDEO
VIDEO
AC IN
MODEL NO. SR5002
FLASHER
IN
PRE OUT
AC OUTLETS
120V 60Hz
SWITCHED
1.25A 150W
CENTER
SURROUND
SURROUND BACK
SPEAKER C/MULTI SPEAKER
FRONT A OR B.CENTER.
FRONT A
+
B : 8 OHMS
SPEAKER
SYSTEMS
FRONT
B
FRONT
A
SURR.SURR BACK : 6-8 OHMS
SURR.SURR BACK : 6-8 OHMS
2
1
5
4
DC
TRIGGER
3
INPUT
3
INPUT 3
OUTPUT
INPUT 2
INPUT 1
HDMI Ver 1.1
COMPONENT
VIDEO
!0
u
!7 @0!8i
y
!1 q r !6
!5
w
o
t
!3
!2
e!9
!4
t MONITOR OUT
This is a monitor output and each one includes both
composite video and S-video confi gurations. When
connecting two video monitors or televisions, be
aware that the OSD interface can be used with both
MONITOR OUT connections.
y Preamp Outputs
(L, R, SL, SR, SBL, SBR, C)
Jacks for L(front left), R (front right), C (Center), SL
(surround left), SR (surround right), SBL (surround
back left) and SBR (surround back right).
Use these jacks for connection to external power
amplifi ers.
u AC INLET
Plug the supplied power cable into this AC INLET
and then into the power outlet on the wall.
This unit can be powered by 230V AC only.
i AC OUTLETS
Connect the AC power cable of component such as
a DVD or CD player to this outlet.
This outlet provides power only when this unit is
turned on.
Caution:
• In order to avoid potential turn-off thumps, anything
plugged into this outlet should be powered up before
this unit is turned on.
• The capacity of this AC outlet is 150W. Do not
connect devices that consume electricity more
than the capacity of this outlet. If the total power
consumption of the connected devices exceeds the
capacity, the protection circuit shuts down the power
supply.
o Speaker outputs terminals
Seven terminals are provided for the front left,
front right, front center, surround left, surround
right, surround back left and surround back right
speakers.
Note:
You can use surround back speaker terminals as M
(Multiroom) SPEAKER B terminals, when you use
no surround back speaker.
q
VIDEO IN/OUT
(TV, DVD, VCR, DSS)
These are the video inputs and outputs. There
are 4 video inputs and 2 video outputs and each
one includes both composite video and S-video
confi gurations. Connect VCRs, DVD players, and
other video components to the video inputs.
The 2 video output channels can be used to be
connected to video tape recorders for making
recordings.
w FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the
terminals marked “AM” and “GND”. The supplied AM
loop antenna will provide good AM reception in most
areas. Position the loop antenna until you hear the
best reception.
e RS-232C (SR5002 only)
The RS-232C port is to be used in conjunction with
an external controller to control the operation of the
SR5002 by using an external device.
r COMPONENT VIDEO INPUT/
OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to these
component video connectors on the unit. This unit
has two component video input connectors to obtain
the color information (Y, C
B
, C
R
) directly from the
recorded DVD signal or other video component and
one component video output connector to output it
directly into the matrix decoder of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra processing
that normally would degrade the image. The result is
vastly increased image quality, with incredibly life like
colors and crisp detail.
When the video convert function is enabled, video and
S-video images can be output to the COMPONENT
MOINTOR OUT jack.
