16
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE. DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
432
1
INSERT
INSERT
INSERT
LINE
INSERT
MIC 4
MIC 3
MIC 2
MIC 1
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
LINE
LINE
LINE
OO
+6
PHANTOM
ON
POWER
ON
120 VAC 50/60 Hz 20W
1A/250V SLO-BLO
16
15 14 13
12 11 10
98765
MIC 16
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
MIC 15 MIC 14
MIC 13
MIC 12 MIC 11
MIC 10
MIC 9
MIC 8
MIC 7
MIC 6 MIC 5
SUB OUT
C-R OUT
MAIN INSERT
(TIP SEND
RING RETURN)
TAPE
TAPE
MAIN OUT
AUX SEND
DIRECT OUT
AUX RETURN
3
R
L
MONO
R
R
R
R
L
R
L
R
L
R
L
L
L
L
1
42
5
1
23
4
3
1
64
2
75
3
8
64
1
2
BAL/UNBAL
BAL/UNBAL
BAL/UNBAL
BAL/UNBAL
BAL/UNBAL
BAL/UNBAL
INPUT
OUTPUT
R
L
(MONO)
(MONO)
(MONO)
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
BAL
UN-
BAL
LINE
LINE
LINE
LINELINE
LINE
LINE
LINE
LINE
LINE
LINE
LINE
TO REDUCE THE RISK OF
FIRE REPLACE WITH SAME
TYPE FUSE AND RATING
CAUTION:
UTILISE UN FUSIBLE DE RECHANGE DE MÊME TYPE. DEBRANCHER AVANT DE REMPLACER LE FUSIBLE
DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA • COPYRIGHT ©1998 • THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGN INC.: "MACKIE", "VLZ", "XDR", AND THE "RUNNING MAN" FIGURE • US PATENT NUMBER 29/049,129
XDR
TM
EXTENDED DYNAMIC RANGE MIC PREAMPLIFIERS ARE PROPRIETARY TO MACKIE DESIGNS, INC.
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
X
D
R
M
I
C
P
R
E
POWER SWITCH
If this one isn’t self-explanatory, we give up.
You can leave this switch on all the time; the
1604-VLZ
PRO is conservatively designed, so
heat buildup isn’t a problem even in 24-hour-a-
day operation. There’s nothing that will burn
out or get used up. You may notice that the
1604-VLZ
PRO’s “pod” feels quite warm (the
pod is the chassis that contains the jacks).
This is perfectly normal.
POWER LED
You’ve probably already figured this out, but
if the
POWER
switch is on, this LED (light-
emitting diode), located in the output section,
will light. If the switch is off, well, you get the
idea. If the
POWER
switch is on and the LED
does not glow, one of three things has hap-
pened: Somebody tripped over the power cord
and yanked it from the outlet, your electricity
has been turned off due to nonpayment, or the
fuse has blown
.
PHANTOM SWITCH
The
PHANTOM
switch controls the phan-
tom power supply for condenser microphones as
discussed at the start of this section
. When
turned on (or off), the phantom power circuitry
takes a few moments for voltage to ramp up (or
down). This is also perfectly normal. For an
even closer look, refer to Appendix C.
PHANTOM LED
Located right next to the
POWER
LED in the
output section, this is just to let you know which
way you have the
PHANTOM
switch set. If your
dynamic mics work and your condensers don’t,
chances are this LED is off, so turn it on.
You’ll notice that when you turn the phan-
tom power off, the LED stays on for a while.
This is a natural phenomenon — the LED is
actually a yellow voltmeter telling you that the
phantom power takes time to ramp itself down
to zero volts. So, if you’ve turned phantom
power off to connect something to the mic in-
puts, wait until the yellow LED stops glowing
and then make your connections safely.
BNC LAMP SOCKET
Located in the top right corner of the out-
put section, this 12V socket will drive any
standard BNC-type lamp (a Littlite
®
#12G or
#12G-HI (high-intensity), for instance).
AUX
SEND
STEREO AUX RETURN
EFFECTS TO
MONITORS
TO AUX
SEND 2
TO AUX
SEND 1
1
2
PWR
PHAN
SOLO
SOLO
1
2
1
2
3
4
1
2
C
-
R / PHNS
ONLY
RETURNS
SOLO
MAIN MIX
TO SUBS
ASSIGN OPTIONS
1
–
2
3
–
4
U
OO
+20
U
OO
+20
U
OO
+15
U
OO
+15
U
OO
+20
U
OO
+20
U
OO
+10
U
OO
+10
LAMP
12 V
0.5A
1604-VLZPRO
16-CHANNEL MIC/LINE MIXER
WITH PREMIUM XDR
TM
MIC PREAMPLIFIERS
