Hunter Fan 41845-01 Manual

Open as PDF

next previous

urur

e 24 - Ae 24 - A

e 24 - A

inin

g tg t

g t

e be b

e b

e te t

e t

o to t

o t

e be b

e b

e ire ir

e ir

n an a

n a

llilli

lli

If you used grommets, the blades may appear slightly loose

after screws are tightened. This is normal.

3. Remove the blade mounting screws and rubber shipping

bumpers from the motor.

4. For each blade, insert one blade mounting screw through the

blade iron as shown in Figure 25, and attach lightly to the fan.

Insert the second blade mounting screw, then securely tighten

both mounting screws.

urur

e 25 - Ae 25 - A

e 25 - A

inin

g tg t

g t

e be b

e b

e ire ir

e ir

n tn t

n t

o to t

o t

e fe f

e f

installing the light fixture

attaching the upper switch housing

1. Partially install two #6-32 x 3/8" housing assembly screws into

the switch housing mounting plate as shown in Figure 26.

2. Feed the upper plug connector through the center opening of

the upper switch housing. See Figure 26.

urur

e 26 - Ae 26 - A

e 26 - A

inin

g tg t

g t

e upe up

e up

r sr s

r s

h hh h

h h

sinsin

sin

g tg t

g t

o to t

o t

unun

inin

g pg p

g p

3. Align the keyhole slots in the upper switch housing with the

housing assembly screws installed previously.

4. Turn the upper switch housing counterclockwise until the

housing assembly screws are firmly situated in the narrow end

of the keyhole slots as shown in Figure 27. Install the one re-

maining #6-32 x 3/8" housing assembly screw into the third

hole in the upper switch housing. Tighten all three screws firmly.

urur

e 27 - Me 27 - M

e 27 - M

unun

inin

g tg t

g t

e upe up

e up

r sr s

r s

h hh h

h h

sinsin

sin

N: MN: M

N: M

e se s

e s

urur

e te t

e t

e upe up

e up

r sr s

r s

h hh h

h h

sinsin

sin

g ig i

g i

s ss s

s s

e-e-

urur

y ay a

y a

d td t

d t

o to t

o t

e se s

e s

h hh h

h h

sinsin

sin

g mg m

g m

unun

inin

g pg p

g p

. F. F

. F

il-il-

il-

urur

e te t

e t

o po p

o p

y ay a

y a

h ah a

h a

d td t

d t

n an a

n a

ll tll t

ll t

hrhr

e he h

e h

sinsin

sin

g ag a

g a

mbmb

y sy s

y s

s cs c

s c

ulul

d rd r

d r

ulul

t in tt in t

t in t

e se s

e s

h hh h

h h

sinsin

sin

g ag a

g a

d lid li

d li

urur

e fe f

e f

llinllin

llin

attaching the lower switch housing

1. Connect the upper plug connector from the motor to the lower

plug connector in the lower switch housing assembly. See Fig-

ure 28.

NOTE: Both plug connectors are polarized and will only fit to-

gether one way. Make sure that both connectors are properly

aligned before connecting them together. Incorrect connec-

tion could cause improper operation and damage to the prod-

uct.

urur

e 28 - Ce 28 - C

e 28 - C

nnnn

inin

g tg t

g t

e pe p

e p

lulu

g cg c

g c

nnnn

2. Place the lower switch housing assembly over the upper switch

housing. Align the side screw holes in the upper and lower

switch housings. Attach the lower switch housing to the up-

per switch housing with three #6-32 x 3/8" housing assembly

screws. See Figure 28.

Blade Iron

Medallion

Switch Housing

Mounting Plate

Upper Switch

Housing

Assembly

Screw

Upper Plug

Connector

Lower Plug

Connector

Upper Switch

Housing

Upper Plug

Connector

Lower

Switch

Housing

Assembly

Screw