1
2
Before Assembly
1. Make sure that the fan voltage (120) is compatible with your own electrical system.
2. Check to make sure that your carton contains all the parts mentioned in the parts list.
NOTE: e box can be used as a work space to prevent any damage on the
ornamental surface.
CAUTION: Before installing, choose a location for mounting the fan where the blades
have at least 7 feet of clearance from all objects and floor. Mount an
outlet box to the ceiling or use an existing box.
CAUTION: Do not mount fan to sheet rock or drywall type materials. To insure
proper support, use the two #1 wood screws to secure mounting bracket to joist
or beam. If the location you choose does not have a suitable support beam, install a
2”x 4” brace between ceiling joists to support.
Tools you Need
1. Phillips Screwdriver
3. Adjustable Wrench
2. Flat Screwdriver
4.Wire Strippers
Screw Package
S1. Wood Screws & Washers
S2. Bracket Screws & Washers
S3. Blade Screws & Rubber Washers
S4. Wire Connectors
S5. Safety Bolt & Nut
S6. "J" Hook
S7. Zip Tie
S8. Screw and Nut for Safety Cable
Quantity
2
2
13
3
1
1
1
1
What You Have
Parts
1. Mounting Bracket
2. Down Rod Assembly &
Rod Supplied
3. Canopy
4. Waterproof Cover
5. Anti-Sway Adapter
6. Flange Cover
7. Downrod Accessory
8. Light Kit
9. Fan Housing & Motor
10. Glass Shade
11. Bulb (13W CFL)
12. Blades (Sold Separately)
13. Wall Control
14. Remote Control
Quantity
1
1
1
1
1
1
1
1
1
1
2
4
1
1
Hardware
Inventory
S6
S4
S5
S2
S3
S7
Trouble Shooting
Problem A: Fan Will not Start
Remedies:
1. Check fuse or circuit breaker and replace if necessary
2. Turn off electrical power and check all wire connectors.
3. Check on/off TCS and wall control selector switch. See operation instructions.
Problem B: Fan is Excessively Noisy
Remedies:
1. Check that all screws in fan assembly are tight and properly seated.
2. Check to make sure mounting bracket is installed properly.
3. Check to make sure light kit and glass are installed properly and tight.
4. If wall control is used, insure the wall control is not a transformer or a variable speed type.
Problem C: Fan Wobbles
Remedies:
1. Check that all blades are screwed firmly into blade holders.
2. Check that all blade holders are screwed firmly into motor.
3. Check the weight of blades. All our blades are weighed on electronic scales. e weight is
marked on the reverse side of the fan blade near the motor end. All of the blades should be
the same weight to prevent fan from wobbling.
4. A balancing kit is enclosed if needed.
2
1
3
8
10
5
4
6
1
1
12
9
14 13
7
S8
Read and Save ese Safety Precautions
1. Turn off electricity at main switch before wiring or servicing fan in order to avoid
possible electrical shock.
2. All wiring must be in accordance with the National Electric Code (ANSI/NFPA70-1999) and local
electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. After making the wire connections, the wires should be spread apart with the grounded
conductor and the equipment-grounding conductor on the one side of the outlet box
and the ungrounded conductor on the other side of the outlet box.
4. e splices after being made should be turned upward and pushed carefully up into the outlet box.
5. Conductor of a fan identified as grounded conductor to be connected to grounded conductor of power
supply, conductor of a fan identified as ungrounded conductor to be connected to an ungrounded
conductor of power supply, conductor of fan identified for equipment grounding to be connected
to an equipment-grounding conductor.
6. To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked
"Acceptable for Fan Support" and use mounting screws provide with the outlet box.
e outlet box and its support must be able to support the moving weight of the fan (at least 35lbs)
7. WARNING: To reduce the risk of fire or electric shock, use this fan only with solid state speed control
device provided.
8. Wall switch, model UC9787TB, the switch have been investigated and found acceptable for use
as a fan speed control.
9. WARNING: To reduce the risk of personal injury, do not bend the blade brackets when installing
the brackets, balancing the blades or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
10. Weight: e weight of the complete fan, incuding assembly hardware is 17.6 lbs.
