Filter
Top Products
Use of Timer Only
General Operation (continued)
General Operation (continued)
Probe
FIG. 3
General Operation
Battery Installation
°C
RESET
°F
°F/°C Slide
Switch
Magnet
Magnet
Battery
Compartment
FIG. 2
Reset
Button
Cooking
Table
LCD
Readout
Set
Temp
Thermo
Temp
Sensor
Plug
Temp
Alert
On/Off
Start/Stop
Temp Set
Up/Down
Hour
Minute
FIG. 1
Probe
Power
On/Off
The thermometer operates on 2 AAA alkaline batteries
(included). There is a strip under the battery cover to prevent
battery drain in shipping. Please remove the strip before
continuing with these instructions (you may need to remove the
battery compartment cover to avoid breaking the strip). If
readings grow dim or irregular, the batteries may need to be
replaced. To replace the batteries:
1. Use 2- AAA alkaline batteries (as installed). Always replace
both batteries at the same time; do not combine old and new
batteries.
2. Remove the battery compartment cover, located on the back
of the unit (FIG. 2).
3. Remove the old batteries from the battery compartment.
4. Place the new batteries into the compartment as indicated by
the polarity symbols marked inside the battery compartment.
5. Replace the battery compartment cover.
Thank you for purchasing the Taylor® Digital Cooking
Thermometer/Timer. Your Thermometer/Timer is an example of
superior design and craftsmanship. This product helps to eliminate
over-cooking or under-cooking foods. Presetting to the recommended
cooking temperatures and/or cooking time is simple and ensures that
food will be cooked to your preferred taste. Please read this
instruction manual carefully before use. Keep these instructions
handy for future reference.
7. Turn TEMP ALERT on for audible alarm. Press the
START/STOP button to begin timing. The thermometer
alarm will automatically sound when the inner temperature
reaches your preset temperature.
8. Press the START/STOP button and the alarm will stop
temporarily. The alarm will produce a 5 second reminder
beep every minute for 5 minutes until you turn it off. To turn
the alarm off, slide the TEMP ALERT switch to the OFF
position.
9. When the food is ready, remove the metal probe from the
meat with a heat resistant glove. DO NOT TOUCH THE
PROBE OR CORD WITH YOUR BARE HAND!
10. Wash the metal probe with hot soapy water. Keep out of
reach of children.
11. In order to preserve the battery, slide the ON/OFF switch
(FIG. 2) to the OFF position when not in use.
1. Turn unit on.
2. Press Hour (HR) and Minute (MIN) button to set time.
Press and hold for speedy setting.
3. After time elapses, alarm sounds for 1 minute. Press
START/STOP to turn the alarm off.
4. Press HR and MIN buttons simultaneously to clear time
set.
1. Preheat the oven to desired cooking temperature.
2. Sterilize the metal probe by inserting it into an appropriate
solution such as boiling water for several minutes.
3. Turn unit on with switch located on the side. Select °F or °C
temperature scale by moving the slide switch on the back of
the thermometer.
4. Insert metal probe into the center of the food to be cooked
(not in contact with bone) and place the food into the oven.
The Electronic Unit must be placed outside of the oven. The
probe cord will be held in place by the oven door (FIG. 3).
5. Make sure the sensor plug (FIG. 1) on the other end of the
cord is plugged into the thermometer. The internal
temperature of the food can now be seen on the display
under Thermo Temp.
6. Adjust the time and temperature by pressing the appropriate
buttons. Press and hold for speedy setting or tap for fine
adjustment. To clear the time setting, press HR and MIN
buttons simultaneously. To clear the time and temperature
settings, press the RESET button on the back of the
thermometer. See the cooking table (FIG. 2) for
recommended temperatures and times to prepare various
meat and fowl.