Filter
Top Products
! Wait until the cleaning cycle has
finished before removing the shaver
from the base. If the shaver is removed
during the cleaning cycle it will be
covered with cleaning solution and be
unusable.
Shaver should be left in cleaning base
for 24 hours to allow it to dry for next
usage.
Solution levels
The cleaning solution will slowly evapo-
rate with use. When the solution levels
get low, the red replacement indicator
light will begin to flash. This means you
have enough cleaning solution left for
approximately 5 more cleanings. If the
red light stops blinking and glows
steadily, the unit will not operate until
the solution and filter have been
replaced.
Replacing the Filter and Solution
Only Remington’s special cleaning
solution and filter can be used with
the Power Clean System. The cleaning
solution contains a high percentage of
alcohol and a special oil that lubricates
your shaver each time it is cleaned. The
filter is specially designed to collect hair
debris yet allow for the system to clean
your shaver.
Remove and discard filter and empty any
remaining cleaning solution. Rinse unit
tank then let dry. Fill with fresh solution,
insert new filter and replace upper
portion.
Wipe off the unit periodically with a
damp cloth and remove any hair debris
that has collected where the shaver sits.
■ To preserve the life of the batteries,
let them fully run out every six
months, then recharge them for
a full 24 hours.
■ Cord/cordless rechargeable shavers
can run directly off the cord if neces-
sary. They will not recharge while you
are shaving, so after shaving with the
cord, turn the unit off and set it aside
to charge. Cord/cordless shavers
should not be used strictly as cord-
operated shavers, as continued cord-
only use will result in reduction of
battery life.
■ Quick Charge provides up to 60 min.
of shaving after a one-hour charge,
or a single shave after a five-minute
charge.
NOTE: If your shaver battery is com-
pletely discharged or the shaver has not
been used for a long time, the shaver
may not start when operated using the
cord. If this happens, charge the shaver
for approximately five minutes before
shaving.
NOTE: It may take up to 3 cycles for the
battery to reach full capacity.
Operating the Cleaning
System
Cleaning
To activate cleaning mode, simply press
the CLEAN button on the cleaning base.
The amber indicator light flashes through
the entire cleaning cycle, which lasts
approximately 2 minutes. When the clean-
ing cycle has been completed, the amber
light will stop blinking and glow steadily.
The unit then returns to charging mode.
9
8
Before using read the important
safety instruction section in front
of the manual.
Preparing the System
Cleaning solution:
1. Press the latch buttons
on the sides of the
cleaning base and lift
the upper portion off
the unit. You will
need to keep the
buttons pressed in
as you move the
upper portion away
from the base. The
cleaning solution
tank is in the unit’s
bottom portion.
2. Remove the filter
from the tank and
set aside.
3. Pour the bottle of
cleaning solution into
the base of the unit
through the opening
where the filter was
removed.
4.
Place the filter back
into its original position.
NOTE: It is important to make sure the
filter is in place. The filter collects hair
clippings and debris, and should be
replaced along with the solution. Failure
to do so will permanently clog the
system rendering it inoperable.
5. Replace the top portion of the clean-
ing base by lining up the three posts
with the three holes in the tank. Push
the top portion down until the two
latches click into place.
6. You can dispose of the bottle and cap
with your normal trash, or recycle where
local ordinances apply.
Charging
Prior to using your shaver for the first
time, put it on charge for 24 hours.
NOTE: It may take up to 3 cycles for the
battery to reach full capacity.
Using Cleaning Base
Plug the power cord into the cleaning
base and then into an electrical outlet.
Make sure arm is in the up position
before inserting shaver. Push down to
release arm. It will "pop-up".
Place the shaver into the unit, head side
down, and slide its “tail” toward the
“neck” of the base until it stops.
Push the arm down until it contacts the
shaver (clicks into place).
Charging
Your shaver automatically begins to
recharge as soon as it is in place in the
cleaning base. While it is charging, the
blue indicator light will flash; when it is
fully charged the blue light will stop
blinking and glow steadily.
Your Shaver can also be recharged by
plugging it into the cord directly.
■ Use only the charging adapter
supplied with the shaver.
■ Make sure your shaver is turned off.
■ Connect the cord to the shaver, then
plug the charging adapter into the
electrical outlet. A charging indicator
light will come on.
■ Your shaver cannot be overcharged,
so you can leave it plugged in and
charging between shaves.
1
2
3
How To Use
30039_R-1000_IB_tri 8/24/06 2:55 PM Page 8