Filter
Top Products
Depending on your shaving technique and
habits, the screens will usually last 6
months; the cutters, 12 months.If you are
replacing the cutters, it’s a good idea to
replace the screens at the same time.
Here are some signs that your foils and
cutters need replacing:
Irritation: As screens get worn, you may
notice that your skin feels more sensitive
after a shave, particularly when you apply
aftershave.
Pulling: As cutters wear,your shave may
not feel as close and you may feel your
shaver is pulling at your whiskers.
Wear-through: You may notice that the
cutters have worn through the screens.
The replacement for this shaver is model
SP-67 (screens) and SP-69 (screens and
cutters).
U.S. residents:
To order shaver accessories call
800-736-4648, visit
www.remington-products.com,
or visit your local retailer.
Canadian residents:
To order shaver accessories,please call
800-268-0425, visit
www.remington-products.com
or visit your local retailer.
9
8
Lubricating
1. Every six months apply a drop of light
machine oil one-third and two-thirds of
the way along the blade.
2. Using your fingertip, spread the oil along
the teeth.
3. Run the trimmer for a few seconds to
distribute oil.
Replacing Cutters and
Screens
To prevent inadvertent damage to the cut-
ters and screens, do not attempt to remove
them from the head assembly unless you
are replacing them. Removal instructions
are included with the cutter and screen
replacement packages.
To replace a cutter assembly that is
removed unintentionally:
1. Hold the assembly in the middle of the
"T".
2. Gently slide the plastic portion of the
cutter assembly over the top of the
oscillator tip.
3. Do not push downward on the ends of
the cutters, as you may bend the cutter,
reducing its ability to operate smoothly.
4. Do not remove cutters from the plastic
pieces they are attached to, as you may
damage the assembly.
When is it time to replace
your screens and cutters?
Because they are subject to
daily use, the cutters and
screens of your shaver will
wear and eventually require replacement to
maintain a close,comfortable shave. It is
very important to replace your screens and
cutters when necessary to ensure a close,
comfortable shave without irritation.
1. Turn the shaver off.
2. Remove the head assembly by squeezing
on both release buttons and pulling up from
the body of the shaver.
3. Use the cleaning brush to
sweep out the cutters and
trimmer.DO NOT USE
THE CLEANING BRUSH
ON THE SCREENS.
Damage may occur to the
holes in the screens.
4. Replace head assembly.Remington
®
Shaver Saver
®
Lubricant (SP-4) lubricates
and cleans your shaver's cutters and head
assembly.The lubricant helps remove hair
clippings while reducing wear.A quick spray
after each shave keeps your shaver operat-
ing at peak performance.
Cleaning Cautions
■The construction of this shaver is for dry
operation only. It is not waterproof.Never
put the shaver in part or completely into
water.
■Do not use an aggressive cleansing agent
as this may destroy the shaver coatings.
■Do not remove or replace the head assem-
bly while shaver is running as it may cause
damage to the unit's screens or cutters.
■Replace worn or damaged parts with
Remington
®
replacement parts only.
Trimmer Care
Cleaning
1. Turn the shaver off.
2. Extend the trimmer to its maximum
height by pressing the right trimmer
button.
3. Use the cleaning brush to sweep off any
clippings that may have accumulated
around the trimmer assembly.Using the
supplied brush will enable you to get into
the area between the trimmer and the
shaver.
Cleaning Your Shaver
Remington® recommends cleaning
your shaver after every use for optimal
performance.
1. Turn shaver OFF.
2. Press side release
button to flip open
head assembly.
3. Screens-Do not use the
brush to clean the
screens. Instead,blow the
shavings out or rinse the
screens under cold or warm water.
4. Cutters and trimmer-Use the cleaning
brush to sweep any loose hairs from the
cutters and trimmers.
5. After cleaning,return the foils and head
assembly to their original position on the
shaver.
6. To clean the external surfaces of the
shaver,use a damp cloth. Do NOT use
strong detergents or other chemicals.
7. To dry, wipe the surface of the overall
shaver with a dry towel. Do NOT use a
hairdryer or heater to dry the shaver.
Screens and Cutters
To assure smooth,efficient performance, it is
important to clean your shaver.
Daily
Blow out the stubble after each shave.
1. Turn the shaver off.
2. Remove the head assembly by squeezing
on both release buttons and pulling up from
the body of the shaver.
3. Thoroughly blow out the stubble from the
screen and cutters.
4. Replace head assembly.
Weekly
Brush out the cutters and trimmer at least
once a week.
Cleaning & Maintenance
27714_MS2_150_IB 9/1/05 10:50 AM Page 8