Philips 282XL Electric Shaver User Manual


 
1. Be certain your razor is
OFF.
First time charging re-
quires a full 8 hours. For
first time or initial charge,
Green Charge Indicator
Light will light to indicate
razor is (re)charging. For
proper use, charge razor
for the full 8 hours as
directed. A fully charged
razor will give approxi-
mately 2 weeks of 3
minute shaves per day.
2. Use only the cord provided.
3. Connect cord to razor and
plug into outlet.
(Re)charge at tempera-
tures between 40°F and
95°F. Charging at lower or
higher temperatures ad-
versely affects lifetime of
batteries.
(Re)charging longer than
required period of time
will not harm razor.
However, continuously
charging razor will reduce
life of batteries.
2A. TO CHARGE
After initial 8 hour charge,
recharging will take only 1
hour to (re)charge batter-
ies to full capacity.
2C. FAST 5-MINUTE
QUICK CHARGE
When battery is totally
depleted, recharging for 5
minutes gives enough
energy for one 3-5 minute
cordless shave.
If razor has not been used
for at least a month, razor
must be recharged for a
full 8 hours (see Section
2A. TO CHARGE).
2B. TO RECHARGE
In North America, Central
America, and South America,
the most common voltage is
between 110V and 130V AC.
When traveling to other coun-
tries, common voltage may
range to 240V AC. Your new
razor will automatically convert
internally to work on 100V to
240V AC systems.
An adaptor plug may be neces-
sary for cord usage in foreign
countries. It is suggested that
you take all adaptor plugs with
you when traveling overseas to
ensure compatibility with most
foreign outlet configurations.
Norelco Travel Adaptor Plug
Kit, model TP5, may be pur-
chased at a store near you or at
a Norelco Service Store.
1. VOLTAGE
3. CORD/CORDLESS
SHAVING
Start with a clean, dry face.
You may choose to use a pre-
shave lotion to set your beard
up for a close, smooth, com-
fortable shave, especially if
you are using an electric razor
for the first time.
CAUTION: It is recommended
that you wash and dry your
hands to remove any remain-
ing lotion before handling
your razor. Some lotions may
cause damage to the exterior
finish of your razor housing.
In addition, clean razor heads
more frequently to prevent
pre-shave lotion build-up.
A. CORD
1. Be certain razor is in OFF
position.
2. Connect cord provided to
razor.
3. Remove Protective Razor
Head Assembly Guard.
4. Plug into 100V to 240V AC
outlet.
5. Slide ON/OFF switch ON.
Begin shaving.
Even when cord shaving,
if battery is low, wait a few
seconds for razor to go
ON.
6. Shave against direction of
beard growth using a quick,
small, circular motion.
4. POP-OUT SIDEBURN,
BEARD AND MOUS-
TACHE TRIMMER
1. Push Trimmer Slide Switch
up to pop out trimmer and
turn razor ON.
2. Hold trimmer, as shown,
to exact hairline desired.
Move trimmer downward
with gentle pressure (Fig. 1).
3. Turn razor OFF and brush
out trimmer section using
long bristles of brush.
4. Close trimmer by pushing
Trimmer Slide Switch down.
Lubricate trimmer teeth
twice a year with Norelco
Razor Lubricant, model
AL80, or one drop of light
machine oil.
1
7. Keep skin taut using your
fingers to stretch skin so
blades can cut whiskers
off.
8. Easy does it. Gently press
razor to your skin so
floating heads can follow
the contours of your face.
9. Turn razor OFF and un-
plug.
It is not recommended
that this razor be used
exclusively as a corded
razor. Continual use as a
corded razor as well as
continuously recharging
razor will reduce life of
batteries.
NOTE: Razor does not re-
charge during shaving.
B. CORDLESS
1. Charge according to
directions.
2. Slide ON/OFF switch ON.
Begin shaving.