Filter
Top Products
13
Replacing the Detergent Cartridge
Note: In order to maintain maximum
cleaning performance, it is
important to replace the water
in the water tank at the same
time you replace the cartridge.
It is recommended to clean the
shaver with the self-cleaning
recharger after every shave.
Change the cartridges when the
status lamp is illuminated. Before
exchange, make sure to inspect the
cartridges with following procedure.
Checking the status lamp
In cases when the status lamp blinks,
carry out the following inspections.
1. Is the detergent cartridge set
properly?
→ Properly set the detergent car-
tridge (see fig. 15).
2. Was the detergent cartridge de-
tached during cleaning?
→ Reset the detergent cartridge.
After completing inspection and treat-
ment
• Properly set the detergent cartridge
to extinguish the status lamp and
start each course.
In cases when the status lamp is
illuminated, detach the shaver from
the self-cleaning recharger and carry
out the following inspections.
• Note that there are cases where the
blade will be hot or wet if cleaning
is not completed.
• Check to ensure that the clean
lamp has been extinguished.
1. Is the water tank and its cap set
properly?
→ Attach the water tank and its
cap properly.
2. Is the self-cleaning recharger
tilted?
→ Place the self-cleaning
recharger on a horizontal surface.
When an abnormality has been
corrected in accordance with the
above two inspections.
• Hold down the select button for
approximately two seconds to ex-
tinguish the status lamp and start
each course.
When no abnormality was found af-
ter the above two inspections.
• It is time to replace the detergent
cartridge and cleaning liquid inside
the water tank. (The same cartridge
has been used to clean approxi-
mately 30 ~ 40 days worth of beard
shavings.)
→ Drain the old cleaning liquid in-
side the water tank and refill the
tank with water. Additionally,
replace the old detergent cartridge
with a new one.
• If the status lamp blinks or
illuminates again even after the in-
spections and treatments above
have been carried out, contact an
authorized service center.
Shaving Cleaning Reusability
1 time/day
1 time/day
1 time/3 days
1 time/1week
approx. 30~40 times
approx. 10~15 times
approx. 4~7 times
Replace the HydraClean™ Shaving
System Solution Cartridge when it
has reached the end of its service
life. Normally, it is recommended to
replace it every 30-40 days if used
once every day. Use the below chart
as a guide.
13
12
3. Pull up the arm of the self-clean-
ing recharger until it clicks (see
fig. 17-3).
4. Remove the protective cap and
set the shaver firmly onto the self-
cleaning recharger until it clicks
(see fig. 17-4).
• Ensure that the outer foil does
not get deformed or damaged
during setting.
• Before using the self-cleaning
recharger, make sure the
shaver has been rinsed
thoroughly with water if it has
been washed with hand soap
or any other detergent, and
swish water off properly before
setting the shaver into the self-
cleaning recharger unit.
The presence of soap or any
other detergent residue will
contaminate the cleaning
solution in the self-cleaning
recharger unit and could lead
to poor cleaning performance.
5. To clean the shaver, select either
the (Clean/Dry/Charge) course or
the (Clean/Dry) course.
To dry the shaver after rinsing,
select the (Dry/Charge) course or
the (Dry) course (see fig. 18).
• The (Charge) course will begin
immediately when the shaver
is set onto the self-cleaning
recharger.
• A total of five courses are
available.
The display will alternate
between (Clean/Dry/Charge)
→ (Clean/Dry) → (Dry/Charge)
→ (Dry) → (Charge) whenever
the select button is pressed.
• The course will start
approximately six seconds
after being selected.
* Press the select button within
six seconds to choose a
different course (see fig. 3).
WARNING – Do not remove the
shaver from the self-cleaning
recharger when courses that
include the (Dry) function are in
use. A heater is used during the
drying process, and this may result
in the area around the blade
becoming extremely hot and
causing burns.
The course will be aborted if the
power is cut off during cleaning. In
this event, it is necessary to perform
the (Clean/Dry/Charge) or (Clean/
Dry) course once again from the be-
ginning.
It will take about 3 hours to finish the
(Clean/Dry/Charge) or (Clean/Dry)
course.
The clean and dry lamp will blink
after the (Clean/Dry/Charge) or
(Clean/Dry) course is completed.
• The self-cleaning recharger is
mainly designed to clean the
blades (outer foil and inner blades).
Areas that are not soaked into the
cleaning liquid or around the sur-
face of the liquid are not subject to
cleaning.
Carry out brush cleaning or wash
with water to remove beard trim-
mings in these areas.
12