Filter
Top Products
98
• Bikini (see fig. 10)
It is recommended to use the pop-
up trimmer for proper shave.
Cleaning
(see fig. 5)
For cleanliness and convenience, we
recommend that you clean your
shaver with water and a liquid hand
soap. Regular cleaning will keep your
shaver in good condition while pre-
venting odors or bacteria from devel-
oping, and maintain the cutting per-
formance.
With the outer foils in place, apply
some hand soap onto the outer foils.
Turn the shaver on and turn off after
few seconds.
Next, press the outer foil frame re-
lease buttons to remove the outer foil
frame and rinse the inner blade/outer
foils under running water or in a ba-
sin.
DO NOT USE BOILING WATER.
Next, close the outer foil frame and
dry it gently. After the shaving head
is dry, place the protective cap.
Replacing shaving head
components
It is recommended that you replace
the outer foil at least once every year
and the inner blade at least once
every two years to maintain your
shaver’s cutting performance.
Replacing the outer foil
(see fig. 2, 3)
Press the outer foil frame release but-
tons to remove the outer foil frame .
Then, squeeze the front and the back
side of the foil frame and lift up one of
the two knobs on the outer foil.
Inserting the new outer foil
Slip the foil into the frame and guide
the plastic edges onto the hooks in
the foil frame until it clicks into the
shaver.
Replacing the inner blade
(see fig. 2, 4)
Squeeze the outer foil release but-
tons and lift the outer foil frame up-
ward to remove it. Remove the inner
blade by grasping it firmly at both
ends and pulling straight away from
the shaver. To insert the new inner
blade, hold the blade at both ends
and press downward until it snaps
into the shaver.
ATTENTION:
The product you have purchased
is powered by a nickel cadmium
battery which is recyclable. At the
end of its useful life, under vari-
ous state and local laws, it is ille-
gal to dispose of this battery into
your municipal waste stream.
Please call 1-800-8-BATTERY for
information on how to recycle this
battery.
How to remove the built-in
rechargeable battery
before disposal of shaver
The battery in this shaver is not in-
tended to be replaced by consumers.
However, the battery may be re-
placed at an authorized service
center. The procedure described be-
low is intended only for removal of the
rechargeable battery for the purpose
of proper disposal.
Caution
• Do not charge the shaver where the
temperature is below 0°C (32°F) or
above 40 °C (104°F), where it will
be exposed to direct sunlight or a
heat source, or where there is a lot
of moisture.
• Use only the included shaver
charging stand RE3-40 to charge
the ES2206 shaver.
• Dry the shaver completely before
setting it in the charging stand.
• Keep the charging stand away from
water and handle it only with dry
hands. Do not use an extension
cord to connect the charging stand
to an outlet.
• The shaver may not immediately
begin to charge after being placed
into the charging stand after use.
Allow the shaver to sit in the charg-
ing stand for a few minutes and
check again to make sure that it is
being charged.
• Store the charging stand in a dry
area where it will be protected from
damage.
WARNING:
Do not attempt to replace the bat-
tery for the purpose of reusing the
shaver. This could result in the
risk of fire or electric shock.
1. Remove four screws (a). (see fig.
11)
2. Remove two screws (b). (see fig.
12)
3. Pull the housing (c) out of the end
cap (d). (see fig. 13)
4. Remove two screws (e) inside of
the end cap and pull the battery.
(see fig. 14)
5. Using a flat screwdriver (f), and
insert into the space (g) to remove
the battery. (see fig. 15)
ATTENTION:
This laws of various states and
municipalities restrict disposal of
rechargeable batteries (and prod-
ucts from which such batteries
have not been removed) in ordi-
nary household waste. Please
comply with your local laws. If you
are not certain as to proper dis-
posal, please contact your local
sanitation department.