Filter
Top Products
SPECIFICATIONS
• Big LCD display
• Minimum capacity: 2.5kg
Maximum Capacity: 150 kg
• Division: 100g (0.2 lb)
• Auto Zero-Auto off
• Low Battery / Overload Indication
• Power: 1 Lithium battery (CR2032)
• Equipped with High Precision Strain Gauge
Sensor System (4 Sensors)
Preparations Before Use
1. Insert the Lithium battery (included). See figure
1 (Note: Make sure battery is pushed all the
way into its slot. Also make sure + side of
battery is facing out)
2. Scale Setup: Place the scale on a hard flat
surface. Tap the front corner (right or left) of
the scale with your foot. The digit “0” will scroll
across the display. Then the display will show
“0.0”This indicates that the scale has been
setup correctly.
a) Note: This “Scale Setup” procedure applies
only after installing a battery. After completing
“Scale Setup”, it does not need to be
performed again unless battery is removed
and replaced.
b) Note: If you step on the platform before “0.0”
appears, you will not obtain a reading. If this
happens, step off the scale, then wait for
display to turn off, follow above steps to setup
scale.
Scale Operation:
To measure weight, simply stand with both feet
in the center of the scale’s glass platform. Be
sure to stand erect and remain still. After 3
seconds the display will flash your weight and
then display it steady.
Note: If a weight less than 10kg is placed on the
scale, the scale will not activate. To weigh
something less than 10kg, activate the scale first
by tapping the front corner (right or left) of the
scale with your foot.
1. When no weight is on the scale for 10 seconds,
the scale will turn off automatically.
Getting Accurate Readings:
1. If the scale has not been used for a long time,
proceed as follows:
a) First, step lightly on the front corner (right or
left) of the scale first to activate the scale.
b) Second, wait for the scale to turn off. Then you
may use the scale normally.
2. If the scale is moved, proceed as follows:
a) remove the battery from the scale for 5
seconds
b) replace the battery
c) follow “Scale Setup” instruction (listed in
Preparations Before Use point 2 above)
3. Place scale on flat hard surface. Do not use
scale on carpet because the reading will be
inaccurate.
4. If the reading appears inaccurate, please
check if the battery and the contact point are
well connected. If scale has been in use for
a long time, replace the battery and try again.
If necessary, contact the local franchisers or
contact our company.
Handling Tips:
1. Store the scale horizontally.
2. Do not overload the scale.
3. The scale is for home use only.
4. Do not submerge scale in water. Use glass
cleaner to clean glass platform of scale.
5. Do not leave any objects on top of scale if the
product is not to be used during a prolonged
period of time. Also remove the battery to
prevent it from being depleted or leaking.
6. To avoid possible injury, do not stand on the
edge of the platform.
7. Place the scale in an area free from direct
sunlight, heating equipment, high humidity, or
extreme temperature change.
8. To avoid slipping, make sure your feet and
the glass platform of the scale are dry before
standing on the scale.
9. Please do not strike, hit or drop objects onto
the glass platform, otherwise, the glass may
break and cause serious injury.
10. Strong magnetic fields may interfere with the
operation of the scale. Avoid operating the
scale in such areas.
Usage Notes:
1. When the display shows ”Err”, it means that
the scale is overloaded.
2. When the display shows ”Lo”, it means that
the battery is low. Please replace the battery as
soon as possible.
3. If scale display shows random digits or scale
does not automatically shut off, proceed as
follows:
a. remove the battery for 10 seconds
b. replace battery
c. follow “Scale Setup” instruction (listed in
Preparations Before Use point 2 above)