Filter
Top Products
MOUNTING ON DOOR MOUNTING ON WINDOW
OPTIONAL MAGNET SPACER OPTION JUMPER POSITIONS
CONNECTING EXTERNAL CONTACTS CONNECTING EXTERNAL GLASS BREAK SENSOR
CHANGING BATTERIES LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date
is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s
normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling
dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear corporation
for consequential damages arising out of or in connection with use or performance of this product or other indirect damages
with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties,
including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as
labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied.
For warranty service on Linear equipment return product, at sender’s expense to:
Linear Corporation Repairs Department
2580 Pioneer Avenue, Suite C
Vista, CA 92083
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fill an important need in portable wireless signalling. However, there
are some limitations which must be observed.
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such,
they have limited transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or
near their operating frequencies, regardless of code settings.
Changes or modifications to the device may void FCC compliance.
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these
facts should be communicated to the ultimate users.
Copyright © 1995 Linear Corporation 211694 A
MOUNT PLATE
TO FRAME
ALIGN MAGNET
PLATE NEXT TO
TRANSMITTER
PLATE AND ATTACH
TO DOOR
1/2" MAXIMUM
SPACE BETWEEN
TRANSMITTER AND
MAGNET PLATES
SNAP TRANSMITTER
ONTO MOUNTING PLATE
1/2" MINIMUM
MOUNT TRANSMITTER
PLATE TO FRAME
ALIGN MAGNET
PLATE NEXT TO
TRANSMITTER
PLATE AND ATTACH
TO WINDOW
SPACE BELOW
PLATE IS REQUIRED
TO SNAP TRANSMITTER
ONTO PLATE
SNAP TRANSMITTER
ONTO MOUNTING PLATE
USE SNAP-ON MAGNET
SPACER WHEN MORE
HEIGHT IS REQUIRED
HOOK SPACER TO
MAGNET PLATE
AND ROTATE TO
LOCK IN PLACE
SQUEEZE SIDE TABS
TO ADJUST MAGNET
HEIGHT
FOUR HEIGHT
POSITIONS
THIS IS THE FACTORY SET
JUMPER POSITION IT SELECTS
THE INTERNAL SWITCH
PUT JUMPER
ON THE MIDDLE
PINS TO USE
EXTERNAL
SWITCH
TAKE JUMPER
OFF TO USE
BOTH
EXTERNAL
& INTERNAL
SWITCH
- OR -
IMPORTANT NOTE:
WHEN USING BOTH
INTERNAL AND EXTERNAL
SWITCHES BOTH SWITCHES MUST
BE CLOSED TO ARM THE TRANSMITTER
WIRE EXTERNAL NORMALLY
CLOSED CONTACTS TO
TERMINALS 1 & 2
ROUTE SENSOR
WIRES UP THROUGH
WIRING SLOT
CONNECT NORMALLY OPEN
GLASS BREAK SENSOR
WIRES TO TERMINALS 2 & 3
MOVE JUMPER FROM
THESE PINS (SELECTS
INTERNAL SWITCH)
TO THESE PINS
(SELECTS GLASS
BREAK SENSOR)
NOTE: THIS TRANSMITTER IS DESIGNED
FOR USE WITH THE UNITED SECURITY
PRODUCTS "WINDOW BUG" GLASS
BREAK SENSOR. OTHER SENSORS
HAVE NOT BEEN TESTED.
SELECTS INTERNAL
SWITCH
(INSIDE POSITION)
SELECTS GLASS
BREAK SENSOR ONLY
(EDGE POSITION)
SELECTS EXTERNAL
SWITCH
(MIDDLE POSITION)
SELECTS BOTH
INTERNAL AND
EXTERNAL SWITCHES
(NO JUMPER)
NOTE: GLASS BREAK INPUT
TERMINALS ARE ALWAYS ACTIVE
INSTALL TWO
DURACELL
TYPE DL 2032
BATTERIES (+)
SIDE UP
LIFT
WHEN BATTERIES ARE LOW, OPEN SENSOR CASE AND
GENTLY LIFT UP END OF BATTERY CLAMP,
SLIDE BATTERIES OUT
REMOVE BATTERIES
FROM THIS END
NOTE: USE OF EXCESSIVE FORCE ON
BATTERY CLAMP WILL RESULT IN DAMAGE
IF NECESSARY
PUSH IN SLOT TO REMOVE
SENSOR FROM MOUNTING PLATE