A SERVICE OF

logo

Open as PDF
next previous
7
ADJUSTMENT TROLLEY LCA030S/LCA060D/LCA70D
WARNING
Before installing read "SAFETY INFORMATION",
Make sure trolley wheels are compabible with the
beam. Tapered wheels are for use only with "I"
beams (IPN) ; flat tread wheels are for use only with
"H" type beams (IPE).
NOTICE
Trolley wheels ride on the top of the lower flange of
the beam.
During assembly lubricate gears, nuts, capscrews,
and all machined threads with applicable lubricants.
Use of antiseize compound and/or thread lubricant
on capscrew and nut threaded areas prevents
corrosion.
Adjustment Trolley
Refer.Dwg.D5230459
According to travelling beam used
The adjustment is realized with the distance washer :
2.5-3-3,5-4-5-15-25 and 42.5 mm thick
(Rep. 23-26-27-28-35-36-43-52).
1. Stack un the washers as notified on the following
sheet.
2. Position the tightening washers Rep. 31.
3. Tighten the nuts Rep. 51 at 55 mdaN.
Tightening washer Distance Trolley Distance Hoist Distance Trolley flange Distance Tightening washer
+ nut washer flange washer washer washer +nut
Rolling beam
Additionnal thickness
of distance washer
Thickness of
distance washer
Thickness of
distance washer
to make use adjustment
Additionnal thickness
of distance washer
to make use adjustment
IPN 220-98
42.5+25+15+5+4+3.5+3+3+2.5+2.5
0
0
2.5+2.5+3+3+3.5+4+5+15+25+42.5
IPN 240-106
42.5+25+15+5+3.5+3+3+2.5+2.5
4
4
2.5+2.5+3+3+3.5+5+15+25+42.5
IPN 260-113
42.5+25+15+4+3.5+3+3+2.5
2.5+5
5+2.5
2.5+3+3+3.5+4+15+25+42.5
IPN 280-119
42.5+25+15+4+3.5+3+2.5
2.5+3+5
5+3+2.5
2.5+3+3.5+4+15+25+42.5
IPN 300-125
42.5+25+15+4+3+3
2.5+2.5+3.5+5
5+3.5+2.5+2.5
3+3+4+15+25+42.5
IPN 320-131
42.5+25+15+4+3
2.5+2.5+3+3.5+5
5+3.5+3+2.5+2.5
3+4+15+25+42.5
IPN 340-137
42.5+25+15+4
2.5+2.5+3+3+3.5+5
5+3.5+3+3+2.5+2.5
4+15+25+42.5
IPN 360-143
42.5+25+4+3.5+3+3+2.5
2.5+5+15
15+5+2.5
2.5+3.5+4+25+42.5
IPN 400-155
42.5+25+4+3.5+2.5
2.5+3+3+5+15
15+5+3+3+2.5
2.5+3+3+3.5+4+25+42.5
IPN 450-170
42.5+15+4+3+3+2.5
2.5+3.5+5+25
25+5+3.5+2.5
2.5+3+3+4+15+42.5
IPN 500-185
42.5+5+4+3+3+2.5+2.5
3.5+15+25
25+15+3.5
2.5+2.5+3+3+4+5+42.5
IPN 550-200
25+15+4+3+3+2.5+2.5
3.5+5+42.5
42.5+5+3.5
2.5+2.5+3+3+4+15+25
IPN 600-215
25+15+4+3.5
2.5+2.5+3+3+5+42.5
42.5+5+3+3+2.5+2.5
3.5+4+15+25
IPE 220-110
42.5+25+15+5+4+3.5+2.5+2.5
3+3
3+3
2.5+2.5+3.5+4+5+15+25+42.5
IPE 240-120
42.5+25+15+4+3.5+2.5+2.5
3+3+5
5+3+3
2.5+2.5+3.5+4+15+25+42.5
IPE 270-135
42.5+25+5+4+3+3+2.5+2.5
3.5+15
15+3.5
2.5+2.5+3+3+4+5+15+25+42.5
IPE 300-150
42.5+25+4+3.5+2.5+2.5
3+3+5+15
15+5+3+3
2.5+2.5+3.5+4+25+42.5
IPE 330-160
42.5+15+5+4+3.5+2.5+2.5
3+3+25
25+3+3
2.5+2.5+3.5+4+5+15+42.5
IPE 360-170
42.5+15+4+3.5+2.5+2.5
3+3+5+25
25+5+3+3
2.5+2.5+3.5+4+15+42.5
IPE 400-180
42.5+15+4+3.5
2.5+2.5+3+3+5+25
25+5+3+3+2.5+2.5
3.5+4+15+42.5
IPE 450-190
25+15+5+4+3+3+2.5+2.5
3.5+42.5
42.5+3.5
2.5+2.5+3+3+4+5+15+25
IPE 500-200
25+15+4+3+3+2.5+2.5
3.5+5+42.5
42.5+5+3.5
2.5+2.5+3+3+4+15+25
IPE 535-210
25+15+4+3+3
2.5+2.5+3.5+5+42.5
42.5+5+3.5+2.5+2.5
3+3+4+15+25
IPE 600-220
25+5+4+3+3+2.5+2.5
3.5+15+42.5
42.5+15+3.5
2.5+2.5+3+3+4+5+25
HE 206
25+15+4+3+2.5+2.5
3+3.5+5+42.5
42.5+5+3.5+3
2.5+2.5+3+4+15+25
HE 220
25+5+4+3+3+2.5+2.5
3.5+15+42.5
42.5+15+3.5
2.5+2.5+3+3+4+5+25
HE 226
25+5+4+3+2.5+2.5
3+3.5+15+42.5
42.5+15+3.5+3
2.5+2.5+3+4+5+25
HE 240
15+5+4+3+3+2.5+2.5
3.5+25+42.5
42.5+25+3.5
2.5+2.5+3+3+4+5+15
HE 248
15+4+3.5+3+3+2.5
2.5+5+25+42.5
.
42.5+25+5+2.5
2.5+3+3+3.5+4+15
HE 260
15+4+3.5+2.5
2.5+3+3+5+25+42.5
42.5+25+5+3+3+2.5
2.5+3.5+4+15
HE 268
5+4+3.5+3+3+2.5
2.5+15+25+42.5
42.5+25+15+2.5
2.5+3+3+3.5+4+5
HE 280
4+3+3+2.5+2.5
3.5+5+15+25+42.5
42.5+25+15+5+3.5
2.5+2.5+3+3+4
HE 288
3+3+2.5+2.5
3.5+4+5+15+25+42.5
42.5+25+15+5+4++3.5
2.5+2.5+3+3
HE 290
5+2.5+2.5
3+3+3.5+4+15+25+42.5
42.5+25+15+4+3.5+3+3
2.5+2.5+5
HE 300
2.5+2.5
3+3+4+5+15+25+42.5
42.5+25+15+5+4+3.5+3+3
2.5+2.5
HE 305
2.5
2.5+3+3+3.5+4+5+15+25+42.5
42.5+25+15+5+4+3.5+3+3+2.5
2.5
HE 310
0
2.5+2.5+3+3+3.5+4+5+15+25+42.5
42.5+25+15+5+4+3.5+3+3+2.5+2.5
0