Filter
Top Products
9
Activation: To activate the cooling function, press
the cooling switch (3) during shaving. The symbol
in the cooling switch shines blue. For best cooling
performance, we recommend to wait a few seconds
after the cooling function has been activated.
Then continue shaving as usual.
Low battery: The symbol
in the cooling switch (3)
starts blinking when the battery is running low and
there is not enough energy left for the cooling
function. You should be able to finish your shave with
activated cooling function.
You can deactivate the cooling function by pressing
the cooling switch again.
Long hair trimmer
To trim sideburns, moustache or beard, press the
release button (8) and slide the long hair trimmer (6)
upwards.
Travel lock
• Activation: By pressing the on/off switch (5) for
3 seconds the shaver is locked. This is confirmed
by a beep sound and the lock symbol in the
display. Afterwards the display turns off.
• Deactivation: By pressing the on/off switch for
3 seconds the shaver is unlocked again.
Manual cleaning of the shaver
(see fig. C/D)
The shaver is suitable for cleaning under running tap
water. Detach the shaver from the power supply
before cleaning it in water.
• Switch the shaver on and rinse the shaver head
under hot running water. You may use liquid soap
without abrasive substances. Rinse off all foam
and let the shaver run for a few more seconds.
• Next, switch off the shaver, remove the Foil &
Cutter cassette and let it dry.
• If you regularly clean the shaver under water, then
once a week apply a drop of light machine oil on
top of the Foil & Cutter cassette.
Alternatively, you may clean the shaver using a brush:
• Switch off the shaver. Remove the Foil & Cutter
cassette (1) and tap it out on a flat surface. Using
a brush, clean the inner area of the pivoting head.
Do not clean the cassette with the brush as this
may damage it!
Clean&Charge station
(models CT6cc/CT5cc/CT4cc/CT3cc/CT2cc)
The Clean&Charge station has been developed for
cleaning, charging, lubricating, disinfecting and
storing your Braun shaver.
Important
• Only use the power supply special electric cord set
supplied with the shaver.
• In order to avoid any leakage of the cleaning fluid,
place the appliance on a flat, stable surface. Do
not tip, move suddenly or transport in any way if a
cleaning cartridge is installed.
• Do not place the appliance in a mirror cabinet, nor
store it over radiators, nor place it on polished or
lacquered surfaces. Do not expose to direct
sunlight.
• The appliance contains flammable liquid.
Keep it away from sources of ignition. No
smoking.
• Keep out of reach of children. Do not refill
cartridge. Use only original Braun refill cartridge.
13 Station power socket
14 Lift button for cartridge exchange
15 Station-to-shaver contacts
16a Level indicator
16b Status light
17 Start button
18 Cleaning cartridge
Installing the Clean&Charge station (see fig. E)
• Remove the protection foil from the Clean&Charge
station display.
• Press the lift button (14) at the rear side of the
Clean&Charge station to lift up the housing.
• Hold the cleaning cartridge (18) down on a flat,
stable surface (e.g. table).
• Carefully remove the lid from the cartridge.
• Slide the cartridge from the rear side into the base
of the station until it snaps into place.
• Slowly close the housing by pushing it down until it
locks.
• Using the special cord set (10), connect the
station power socket (13) to an electrical outlet.
Charging the shaver in the Clean&Charge station
Insert the shaver head down into the Clean&Charge
station.
Important: The shaver needs to be dry and free
from any foam or soap residue!
The contacts (7) on the back of the shaver need to
align with the contacts (15) in the Clean&Charge
station. Push the shaver in the correct position.
A beep sound confirms that the shaver sits properly
in the station. Charging will start automatically.
Cleaning the shaver in the Clean&Charge
Station
When the cleaning indicator
lights up in the shaver
display, insert the shaver into the Clean&Charge
station, upside down and with the front showing.
Start automatic cleaning
Start the cleaning process by pressing the start
button (17). If the status light (16b) does not shine
(Clean&Charge station switches to stand-by after
about 10 minutes), press the start button twice.
92388019_CoolTec_NA_S6-36.indd 992388019_CoolTec_NA_S6-36.indd 9 10.10.12 13:1810.10.12 13:18