Braun 5000 Electric Toothbrush User Manual


 
17
Pressure sensor
If you put excessive pressure on your teeth, the
red pressure sensor light (b) will light up (picture 3,
page 5). Additionally, when brushing in Daily Clean
or Deep Clean mode, the brushing mode will change
to the «Sensitive» mode. Periodically check the
operation of the pressure sensor by pressing moder-
ately on the brush head during use.
Brushing modes
Your toothbrush offers different brushing modes:
«Daily Clean» – Standard mode for daily
mouth cleaning
«Deep Clean» – Mouth cleaning with
extended brushing time of
45 seconds per quadrant
(3 minute total brushing time
«Sensitive» – Gentle, yet thorough cleaning
for sensitive areas
«Polish/Whitening»
– Polishing for occasional or
everyday use
«Gum Care» – Gentle vibration for gum
Your toothbrush automatically starts in the «Daily
Clean» mode. To switch to the other modes, succes-
sively press the mode button (picture 4, page 5).
To return from any mode back to the «Daily Clean»
mode, press and hold the mode button.
The brushing mode is memorized even when the
handle is briefly switched off during brushing. When
pausing longer than 30 seconds or briefly pressing
the mode button (d) during pause the brushing
mode resets to the «Daily Clean» mode.
Brush heads
Oral-B offers you a variety of different brush heads
that fit your Oral-B DENTA-PRIDE 5000 toothbrush.
Oral-B FlossAction
features micropulse bristles that allow
for an outstanding plaque removal in
the interdental areas.
Oral-B ProWhite
features a special polishing cup to
naturally whiten your teeth. Please
note that children under 12 years old
should not use the Oral-B ProWhite
brush head.
Oral-B Interdental
cleans between teeth, around bridges,
crowns and implants. Position the
brush head at a 45 degree angle to
the gumline. Slowly guide it along the
gumline, pausing between each tooth.
All brush heads feature light blue INDICATOR
bristles to help you monitor brush head replacement
need. With thorough brushing, twice a day for two
minutes, the blue color will fade halfway down
approximately in a 3-month period. If the bristles
splay before the colour recedes, you may exert too
much pressure on teeth and gums.
We do not recommend using the Oral-B FlossAction
or Oral-B ProWhite brush head with braces. You
may use the Oral-B Ortho brush head, specifically
designed to clean around braces and wires.
Synchronizing your toothbrush
To avoid interference of display messages when
using more than one Oral-B DENTA-PRIDE 5000
toothbrush with SmartGuide in the same household,
you need to assign the handles to their respective
SmartGuide.
You can synchronize a maximum of 2 handles with
one SmartGuide. To do so, push the «h/min» button
in the battery compartment for at least 3 seconds.
The SmartGuide shows «L---». Turn on your handle
to start the synchronization process. It is finished
when «L-1-» is displayed. Turn off the handle. To
assign a second handle to the same SmartGuide
turn on the other handle until «L-2-» is displayed.
After having synchronized the second handle, «Full»
will be displayed. Exit the syncronization mode by
pressing the «h/min» or «set» button, otherwise it will
end automatically after 30 seconds.
Cleaning recommendations
After brushing, rinse your brush head under running
water with the handle switched on. Switch off and
remove the brush head. Clean handle and brush
head separately; wipe them dry before reassembling.
Disassemble the charging unit before cleaning. Brush
head compartment and protective cover are dish-
washer-safe. Both basic charger and SmartGuide
should be cleaned with a damp cloth only (picture 5,
page 5).
Wall mount
Use the adhesive tape (k) if you prefer to mount the
SmartGuide on a wall, mirror or other surface. Make
sure the chosen surface is clean and dry. Position
the wall mount (j) with the Oral-B logo readable and
press it evenly and firmly to the wall. Wait 24h before
sliding the SmartGuide into the fixed wall mount
99746373_D34_Japan.indd 1799746373_D34_Japan.indd 17 02.02.11 11:4602.02.11 11:46