Filter
Top Products
CHANGING THE BLADE ASSEMBLY
If your clipper blades no longer cut properly (be sure to try
more than one blade, since blade currently being used may
be dull), it could be that your blade drive assembly needs
replacement.
To change the blade drive assembly:
1. Unplug your clipper.
2. Remove blade set.
3. Remove four housing
screws with philips
screwdriver.
4. Turn clipper over and
remove cover.
5. Before attempting to
remove the blade drive
assembly, you must
remove the blade hinge
first. Remove the
two blade hinge screws
(Diagram H). When
removing the blade hinge,
you will notice a small
spring set in between
the hinge and the lower
housing (Diagram I).
Make sure that this part
does not get lost when
replacing the blade drive
assembly.
6. Remove blade drive
mounting screws
(Diagram J).
7. NOTE: Before removing
blade drive assembly,
note the way it is posi-
tioned (this will help you in
reassembly). Remove
blade drive assembly
(Diagram K).
8. Drive bearing should be at
its lowest position, if not,
move it with your finger
to lowest position
(Diagrams L and M).
9. Align screw holes of new
blade drive assembly and
press down level at the
screw holes (Diagram N).
10. Reassemble blade drive
mounting screws
(Diagram J).
11. Be sure the hinge spring
is in its place before
attempting to replace the
blade hinge and screws
(Diagram O). When replac-
ing the hinge screws,
place screw in the screw
hole and slowly turn
counter-clockwise until
you feel the screw drop
into place. This assures
the screw is properly
aligned within the hole
threads. Turn screw clock-
wise to tighten, just until
snug. DO NOT OVER-
TIGHTEN.
12. Replace cover and turn
clipper over.
13. Replace housing screws
(Short screws in back by
cord—long screws in
front by blade).
FACTORY REPAIR SERVICE
When the blades of your Andis Clipper become dull after
repeated use, it is advised to send your blades to an Andis
Authorized Service Station mentioned below for resharpen-
ing. If you wish your clipper to be serviced as well, they
should be carefully packed and mailed either Parcel Post
Insured, or U.P.S.
To find an Authorized Service Station near you log on
to www.andis.com or contact our customer service
department: 1-800-558-9441 (U.S.)
1-800-335-4092 (Canada)
LIMITED WARRANTY
This Andis product is warranted against defective material or
workmanship for one year from the date of purchase. All implied
warranties arising and by virtue of State law shall also be limited
to one year. Any Andis product determined to be defective in
material or workmanship during the warranty period will be
repaired or replaced without cost to the consumer for parts and
labor. The defective product must be returned with proof of
purchase and $6.50 to cover cost of handling, to any Authorized
Andis Repair Station or to: Andis, 1800 Renaissance Blvd., P.O.
Box 085005, Racine WI 53408-5005 USA or IN CANADA to:
A & AG AGENCIES (CANADA), INC. 10050 Côte de Liesse,
Lachine, Québec, H8T 1A3 CANADA. Enclose or attach a letter
describing the nature of the problem. Due to foreign matter
sometimes found in hair, clipper blades or resharpening of
blades are not subject to the one year warranty. The blade set
has a 10 Day Limited Warranty. If the blade set fails to cut, it will
be resharpened free of charge if returned within 10 days of
purchase. Send your blade set postage prepaid with the original
purchase receipt to:
ANDIS COMPANY, ATTENTION: Service
Department, 1800 Renaissance Blvd, Sturtevant, Wisconsin
53177 (U.S. & Canada only).
Andis will not be liable under this
warranty for any defect, failure or malfunction of any of its
products caused by normal wear, abuse, misuse, unauthorized
adjustments or disassembling. Andis will not be liable for any
consequential damages resulting from any defect in material or
workmanship of any of its products. Some States do not allow
limitations on how long an implied warranty lasts or exclusion
or limitation of incidental or consequential damages, so the
above limitations or exclusions may not apply to you. The
Warranty gives you specific legal rights, and you may also have
other rights which may vary from State to State.
Date Purchased
–––––––––––––––––––
Model
––––––––––––
KEEP THIS FOR YOUR RECORDS
Form # 27074 Rev. P ©2007 Andis Company, USA Printed in U.S.A.
DIAGRAM H
DIAGRAM I
DIAGRAM O
HINGE
SCREWS
SPRING
DIAGRAM H
DIAGRAM I
DIAGRAM O
HINGE
SCREWS
SPRING
Congratulations –
you just went First Class when you bought
this Andis Clipper. Careful workmanship and
quality design have been the hallmarks of
Andis products since 1922.
®
Detachable Plus
®
MODEL AG
Clipper
Andis Model AG
Detachable Blades
are compatible with
Oster Model A5